WhatsApp us
Request a Quote

Project reports in Metal Products

Carbide Tips and Indexable Inserts Plant Project Report

Plant cost, powder-to-coating machinery, raw materials and five-year profitability for a carbide insert plant, with a free sample report PDF you can open now.

Plant capacity
2,900 inserts per day
Total project cost
₹728 lakh
Plant and machinery
₹353 lakh
Return on investment
19% (Year 3)
Break-even
35% of capacity
Payback period
About 3.8 years

Figures from our illustrative sample report for a typical unit. They show the format of an NPCS report and are not quotes for your project.

What is a carbide tips and indexable inserts project report?

A carbide tips and indexable inserts project report is a detailed project report (DPR) for a plant that presses tungsten carbide and cobalt powder into insert shapes, sinters, grinds and coats them. It sets out the process, machinery, raw materials, market, project cost, means of finance, five-year projections, DSCR and break-even that a lender reviews.

Promoters use it to choose a production route and raise a term loan; banks and investors use it to judge whether the plant can repay.

Also known as: carbide inserts project report, carbide insert manufacturing business plan, tungsten carbide inserts DPR, cemented carbide cutting tool plant report.

Carbide insert manufacturing plant cost and economics

Our sample report models a plant making 2,900 inserts per day, or 9,57,000 a year over 330 working days. It starts at 60% of capacity and reaches 80% in Year 5, selling at ₹124 per insert before GST.

Machinery is only about half the bill. Buildings for a dust-controlled pressing room, a furnace bay and a clean coating area add ₹195.58 lakh in the sample.

₹728 lakhTotal project cost
₹831 lakhSales in Year 3
₹140 lakhNet profit in Year 3
1.70Average DSCR
Cost of project (₹ lakh)
Land and site development54.89
Building and civil works195.58
Plant and machinery352.77
Other fixed assets52.14
Contingencies27.42
Preliminary and pre-operative17.07
Working capital margin27.71
Total727.58
Means of finance (₹ lakh)
Promoter's contribution (25%)181.90
Term loan from bank (75%)545.68
Cash credit limit (separate)83.13
Total project cost727.58

Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments; lowest DSCR 1.49 in Year 2. All figures are illustrative.

Carbide insert manufacturing process, from powder to coated edge

Inserts are made by powder metallurgy: metal powders are pressed and then fused by heat rather than melted and cast. The full route has eight stages.

  1. Milling and mixing

    Tungsten carbide, cobalt and grain growth inhibitors are milled in an attritor with solvent and pressing wax until the slurry is even.

  2. Spray drying

    A closed-loop dryer turns the slurry into free-flowing granules that fill press dies evenly.

  3. Pressing

    A CNC press compacts the granules in multi-cavity dies into green inserts, made oversize to allow for shrinkage.

  4. Dewaxing and sintering

    The wax is burnt off and the parts are sintered at about 1,400 degrees Celsius, shrinking about a fifth in each direction. A sinter-HIP furnace adds argon pressure to close pores.

  5. Grinding

    Double-disc grinders finish the top and bottom faces, then periphery grinders form the sides and corner radius with diamond wheels.

  6. Edge honing

    Each cutting edge is brushed or blasted to a small, even radius so it does not chip in the first cut.

  7. Coating

    Inserts are coated in a PVD chamber with layers such as titanium aluminium nitride to slow wear.

  8. Inspection and packing

    Each batch is checked for hardness, density and dimensions, laser marked with the grade and packed in boxes of ten.

Which production route suits a new carbide insert unit?

The biggest decision is how far back in the chain you start. Each step you add raises investment and know-how, but also the margin you keep.

Grind and coat bought blanksBuys sintered blanks and adds grinding, edge prep and coating. Lowest entry cost and fastest start, but margins depend on the blank supplier.
Press to coat (sample route)Buys ready-to-press graded powder and does pressing, sintering, grinding and coating. Controls quality and geometry; needs furnace and press know-how.
Powder to coatAlso mills and blends its own grades from tungsten carbide, cobalt and additives. Most control over grades, with the highest investment and the longest trials.
Brazed carbide tipsPresses and sinters simple tips for brazing onto tool shanks. Simpler grinding and no coating, but a smaller, more price-driven market.
PVD or CVD coatingPVD runs at lower temperature and keeps a sharp edge, which suits milling and finishing. CVD gives thicker layers for heavy turning of steel and cast iron but needs a larger plant.

A common path: start by grinding and coating, build a customer base, then add pressing and sintering once volumes justify the furnace.

Raw materials for carbide tips and inserts

Raw materials are 43.4% of sales in the sample, and tungsten carbide powder alone is 68% of that bill. Tungsten and cobalt prices swing with world supply, so your report should test a price rise against DSCR.

Raw materialShare of costYear 3 (₹ lakh)
Tungsten carbide powder68%245.38
Cobalt powder17%61.35
Mixed carbides and grain growth inhibitors6%21.65
PVD coating targets and process gases6%21.65
Pressing wax and milling solvent3%10.83
Total100%360.86

Grinding scrap and sludge still hold tungsten and cobalt, so many plants collect and sell them to recyclers rather than dump them.

Machinery for a carbide insert plant

In the sample the insert grinders are the largest machinery item, ahead of the sinter-HIP furnace. Grinding capacity, not pressing, usually sets how many inserts the plant can ship.

MachineWhat it doesSample cost (₹ lakh)
Attritor mill and spray dryerMixes powders and makes press-ready granules49.39
CNC powder compacting pressPresses green inserts in multi-cavity dies56.44
Sinter-HIP vacuum furnaceDewaxes and sinters to full density70.56
Double-disc and periphery grindersGrind faces, sides and corner radius77.61
Edge honing and wet blastingPrepares the cutting edge14.11
PVD coating systemApplies the wear-resistant coating56.44
Quality labTests hardness, density and geometry17.64
Laser marking and packingMarks the grade and packs by code10.58
Total plant and machinery352.77

Sample estimates only. Imported furnaces, coaters and five-axis grinders vary widely in price; get current quotations before you finalise.

Utilities and manpower for an insert plant

Furnace cycles run for many hours and cannot be paused, so power quality and gas supply matter more here than in most engineering units.

Power₹72.83 lakh in Year 3 in the sample, about 8.8% of sales. The furnace, grinders and coater are the main loads.
Backup powerA DG set is included in other fixed assets. A power cut during sintering can scrap the whole furnace load.
Industrial gasesHigh-purity argon for sintering under pressure, nitrogen for the spray dryer loop, and process gases for the PVD coater.
Cooling and airChilled water for the furnace, coater and grinding coolant; clean, dry compressed air for presses and blasting.
Manpower22 people in the sample: 3 in management and supervision, 8 skilled operators and 11 semi-skilled and unskilled workers.

Licences and standards for carbide inserts

Business registrationUdyam (MSME) registration and GST registration
Pollution board consentConsent to establish and operate from the State Pollution Control Board. Ask how the board treats cobalt-bearing grinding sludge and spent milling solvent.
Factory licence and fire NOCUnder the Factories Act where thresholds apply, and fire safety approval for solvent and gas storage; rules vary by state
Insert designationIS 9897, identical to ISO 1832, sets the code (such as CNMG 120408) that buyers use to order inserts
Wiper insert dimensionsIS 11523:2026 covers dimensions of carbide inserts with wiper edges and no fixing hole, if you make them

BIS details checked October 2026. Confirm state approvals with your District Industries Centre.

Who buys carbide inserts in India?

Every CNC lathe and machining centre uses inserts, and shops reorder them every month as edges wear. Imported and multinational brands hold most of the coated insert market, so a domestic maker usually wins on price, quick delivery and special geometries.

Buyers judge an insert by tool life on their own job. Expect trial orders, where your insert runs against the brand they use now, before any regular business.

  • Auto component manufacturers
  • CNC job shops in machining clusters such as Pune, Coimbatore, Rajkot and Faridabad
  • Cutting tool distributors and dealers
  • Bearing, valve and pump makers
  • Tool, die and mould makers
  • Heavy engineering and railway workshops

Where a new unit wins: short runs of special forms, grooving and threading profiles that importers do not stock, delivered in days rather than weeks.

Mistakes that weaken a carbide insert project report

  • Pricing at imported brand rates

    New domestic inserts sell below the leading brands until they prove tool life. Using brand prices inflates sales and DSCR.

  • Assuming every pressed insert is sold

    Cracks, distortion in the furnace and out-of-tolerance grinding all cause rejects, especially in the first year of trials.

  • Leaving out diamond wheels and press tooling

    Grinding wheels wear fast on carbide, and each new insert shape needs its own press die. Both are recurring costs.

  • One grade for every material

    Steel, stainless steel and cast iron need different grades and coatings. A report that plans one grade cannot reach most buyers.

  • No plan for cobalt dust

    Fine cobalt and carbide dust is a health hazard. Dust extraction, wet grinding and protective equipment belong in the capital budget.

How NPCS helps you plan a carbide insert plant

  • Route and product rangeChoose between grinding bought blanks and full press-to-coat, and the shapes and grades to launch with.
  • Machinery and suppliersCompare presses, sintering furnaces, grinders and coaters, with quotations for your capacity.
  • Bank-ready project reportProjections, DSCR and working capital, with powder price and yield tested against repayment.
  • Layout and approvalsSeparate powder, furnace and coating areas, power and gas loads, and the approvals list for your state.

NPCS's client list includes 116 assignments for metal products units. The NPCS project team, led by founder Ajay Kumar Gupta, has prepared project reports and feasibility studies since 1994.

What's inside the carbide tips and indexable inserts sample report

  1. Introduction
  2. Uses and applications
  3. Market potential
  4. Manufacturing process
  5. Raw materials
  6. Plant and machinery
  7. Land, building and utilities
  8. Manpower
  9. Licences and approvals
  10. Project cost and means of finance
  11. Working capital
  12. Projected profitability
  13. Cash flow statement
  14. Projected balance sheet
  15. Depreciation
  16. Term loan repayment
  17. Debt service coverage
  18. Break-even analysis
  19. Financial ratios
  20. Key assumptions
  21. Conclusion
  22. Monthly loan repayment schedule

18 pages, five-year projections, illustrative figures.

Open sample report

Free sample or a report for your project?

What you getFree sampleNPCS report for your project
Capacity and locationTypical unitYour capacity, site and state
FiguresIllustrativeBuilt on current prices and quotations
Machinery suppliers and quotationsNoYes
Market survey for your regionNoYes
Bank or scheme format (PMEGP, term loan)NoYes
Use for a loan applicationNoYes

Real NPCS carbide tips and indexable inserts project reports

These are carbide tips and indexable inserts project reports NPCS has prepared, with the plant capacity, total capital investment, rate of return and break-even worked out in each. Costs have moved since some were written, so we bring any of them up to date for your capacity and location.

Project reportPlant capacityTotal investmentRate of returnBreak-evenAction
Carbide Tips Inserts & Indexable1000 Nos./Day₹87 lakh39%50.9% Get this report

Figures as worked out in each NPCS report. Total investment includes plant and machinery, land and building, and working capital.

Find other projects that fit your budget Search NPCS project profiles by investment, return and break-even, the same search as our Startup Selector.

What clients say about NPCS

4.7

264 Google reviews, as of 20 Oct 2026

Clients most often mention

  • feasibility reports 18
  • project report 16
  • helpful for startups 15
  • detailed reports 8
Read all reviews on Google
  • Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.

    Piyush Singh, Google review, 2026

  • Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended

    Saroj Yadav, Google review, 2026 View on Google

  • In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.

    Shrishti Gautam, Google review, 2026

  • NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.

    Raj Yadav, Google review, 2026

Carbide Tips and Indexable Inserts project report: frequently asked questions

What is the cost of a carbide insert manufacturing plant in India?

Cost depends mostly on the route. A plant that grinds and coats bought-in blanks needs far less than one that presses and sinters its own. Our sample report models a press-to-coat plant of 2,900 inserts per day at ₹727.58 lakh, with ₹352.77 lakh of plant and machinery. Imported furnaces and coaters can raise this, so the report should use current quotations.

What raw materials are used to make carbide inserts?

Tungsten carbide powder is the main input, bonded with cobalt powder. Small additions of titanium, tantalum, niobium, vanadium or chromium carbides control grain growth and suit the grade to steel or cast iron. In our sample report tungsten carbide powder is 68% of raw material cost and cobalt 17%; coating targets, gases, wax and solvent make up the rest.

How are indexable carbide inserts made?

Powders are milled with wax, spray dried into granules and pressed into oversize insert shapes. The pressed parts are dewaxed and sintered at about 1,400 degrees Celsius, where they shrink to size. They are then ground on diamond wheels, edge honed, coated in a PVD or CVD chamber, inspected, laser marked and packed.

What is the difference between carbide tips and indexable inserts?

Carbide tips are brazed onto a steel shank, so the whole tool is reground and reused when the tip wears. Indexable inserts are clamped in a holder and have several cutting edges; when one edge wears the insert is turned to a fresh edge and finally thrown away. Both start as sintered carbide, but inserts need tighter grinding and usually a coating.

Is a carbide insert plant profitable?

In our illustrative sample, the plant reaches a 19% return on investment in Year 3 and breaks even at 35% of capacity. It pays back in about 3.8 years, with an average DSCR of 1.70. Real results depend on powder prices, sintering yield, the grade and geometry range you can sell, and how well you win repeat orders from machine shops.

What does an insert code such as CNMG 120408 mean?

It is the designation set out in IS 9897, identical to ISO 1832. The letters give the insert shape, clearance angle, tolerance class and type of fixing hole or chip breaker. The numbers give the cutting edge length, thickness and corner radius. Using this system lets your inserts fit standard holders and be ordered by code.

Is the sample report free and can I use it for a loan?

The sample is free to view and download. It is an illustrative report that shows the format and depth of an NPCS report. Its figures are representative and not based on a real project, so it should not be submitted to a bank. For a loan, NPCS prepares a report for your own capacity, route, location and lender.

Sources and references

  1. IS 9897: Indexable inserts for cutting tools, designation (identical to ISO 1832)Bureau of Indian Standards, checked Oct 2026
  2. IS 11523:2026 Indexable hardmetal (carbide) inserts with wiper edges, without fixing hole, dimensionsBureau of Indian Standards, checked Oct 2026
Ajay Kumar Gupta, founder of NPCS

Who prepares NPCS reports

The NPCS project team, led by Ajay Kumar Gupta

This page and its sample report are prepared and reviewed by the NPCS project team, which has written techno-economic feasibility studies and detailed project reports since 1994.

Ajay Kumar Gupta founded Niir Project Consultancy Services (NPCS) and leads the organisation. With 40 years of experience in MSME project consulting, he has built the team that has delivered more than 28,000 project reports for clients worldwide, helping entrepreneurs plan and finance profitable manufacturing businesses.

Ajay Kumar Gupta on LinkedIn

Published
Last updated
Next review
Oct 2027
Reviewed by
NPCS project team

This page is reviewed every 12 months, or sooner when scheme limits, GST rates, BIS rules or pollution categories change. The sample report is illustrative: its figures are generated from industry-typical ratios for a unit of this size, checked so every statement balances, and are not taken from any client project.

Planning a different metal products project?

These are a few of the projects we advise on. NPCS's published client list records 116 metal products assignments, so tell us what you are planning.

Tell us your project

Recent metal products assignments

  • Long Island Trading Co. Pvt. Ltd
    Project Report on Aluminium Can Manufacturing Plant SetupIndore, 2026
  • Allotrope Engineers
    Bankable Project Report on Gas Atomized Aluminium PowderHyderabad, 2026
  • P M Infrastructure Private Limited
    Comprehensive Market Research Report on TMT BarsBangalore, 2026
  • Arham Recycling Private Limited
    Pre-Feasibility Report on Copper Wire RecyclingFaridabad, 2026
  • Bihar Foundry & Castings Limited
    Industrial Project Report on Electrolytic Manganese MetalRanchi, 2026
  • Rgcon Itm
    Comprehensive Project Report on Copper CathodeVisakhapatnam, 2026
  • Krishnay Recycling Pvt Ltd
    Pre-Feasibility Report on Project Planning and Feasibility Report on Copper Cathode and CoSouth Africa, 2026
  • Goodluck India Ltd
    Techno-Economic Project Report on Inner Grooved Copper TubesSikandrabad, 2025

Get a carbide tips and indexable inserts project report for your plant

Tell us your planned capacity, location and loan scheme. Our team will confirm the scope and price of a report built on current machinery quotations and raw material prices for your region.

Reports are prepared in the format banks and PMEGP offices ask for, with five-year projections, DSCR and break-even.

Request a Carbide Tips and Indexable Inserts Project Report

Share your plan and our team will call you back within 24 hours.

Start with the sample, then plan your own unit

Open the free carbide tips and indexable inserts sample report to see the format, then talk to NPCS about a report for your capacity and location.

Sample PDF WhatsApp
Carbide Tips and Indexable Inserts sample project report (illustrative) Download New tab

Illustrative sample. Figures are representative and not from a real project.

Call Us WhatsApp