What is a aluminium utensils project report?
An aluminium utensils project report is a detailed project report (DPR) for a press shop that draws and spins aluminium circles into pots, kadais and cooker bodies. It sets out the process, machinery, raw material cost, ISI licence, project cost, five-year projections, DSCR and break-even a lender needs.
Entrepreneurs and existing utensil makers use it to size the plant and raise a term loan; banks use it to judge whether the unit can repay.
Also known as: aluminium vessels, aluminium bartan, aluminum cookware, aluminium household utensils.
Aluminium utensils manufacturing plant cost in India
Our sample project report on aluminium utensils models a plant that buys aluminium circles and makes 1,700 kg of utensils per day over 330 working days. It starts at 60% of capacity, reaches 80% in Year 5 and sells at ₹420 per kg ex-factory.
Utensils are priced by weight, so the whole project turns on the gap between the circle price and the selling price per kg. In Year 3 of the sample, total cost including depreciation and interest comes to ₹384.4 per kg.
| Land and site development | 32.16 |
|---|---|
| Building and civil works | 151.32 |
| Plant and machinery | 279.13 |
| Other fixed assets | 27.52 |
| Contingencies | 21.52 |
| Preliminary and pre-operative | 12.79 |
| Working capital margin | 58.82 |
| Total | 583.26 |
| Promoter's contribution (25%) | 145.82 |
|---|---|
| Term loan from bank (75%) | 437.44 |
| Cash credit limit (separate) | 176.46 |
| Total project cost | 583.26 |
Watch Year 2, not Year 1: the debt service coverage ratio (DSCR, cash available for repayment divided by what is due) is lowest at 1.40 in Year 2. That is when full principal repayments begin.
Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments. All figures are illustrative.
Aluminium utensils manufacturing process
Most utensils are formed cold from flat circles, with no melting on site. A pot or kadai body takes one or two press strokes, then goes to the spinning lathe, the buffing line and, for the anodised range, the acid baths.
- Circle inspection
Incoming circles are checked for grade, thickness and surface marks, because a scratch on a circle becomes a visible line on the finished pot.
- Annealing
Hard-temper circles are softened in an annealing furnace so they stretch during drawing instead of tearing at the base corner.
- Deep drawing
A hydraulic press pushes the circle into a die to form the body; deep items such as cooker bodies need a second draw with re-annealing between stages.
- Spinning and trimming
The body is spun against a former on a lathe to true the shape, thin the wall evenly and trim the rim to height.
- Beading and fitting
Rims are curled or beaded for strength and handles, lugs or lids are riveted on.
- Buffing and anodising
Buffing wheels with polishing compound give the bright finish; anodised items are cleaned, anodised in sulphuric acid and sealed.
- Inspection and packing
Each lot is checked for wall thickness, weight and finish against IS 1660, marked and packed in cartons.
Buy aluminium circles or make them in-house?
This is the biggest technology decision in an aluminium utensils project. A press shop buys ready circles from rolling mills and needs only forming and finishing machines. That is the route modelled in our sample report.
An integrated unit melts ingots or scrap, casts slabs, hot and cold rolls them to sheet and blanks its own circles. It controls grade and saves the circle maker's margin. But it adds a melting furnace, a rolling mill and annealing capacity, so the project costs several times more than a press shop of the same output.
A middle path is to buy coil or sheet and blank circles on a power press. It cuts circle cost a little, but the skeleton scrap left after blanking has to be sold back or remelted.
Raw material rule from December 2026: the BIS list of upcoming orders shows wrought aluminium for utensils (IS 21) coming under a Quality Control Order from 1 December 2026. A press shop should plan to buy ISI-marked circles from licensed suppliers.
Raw materials for aluminium utensils
Aluminium circles are 88% of raw material cost in our sample, and raw materials as a whole are 65.3% of sales. Circle prices follow the aluminium price, so most units buy against monthly price lists and hold about 30 days of stock.
| Raw material | Share of cost | Year 3 (₹ lakh) |
|---|---|---|
| Aluminium circles of IS 21 utensil grade | 88% | 947.94 |
| Handles, lids and rivets | 6% | 64.63 |
| Buffing and polishing compounds | 3% | 32.32 |
| Anodising chemicals | 3% | 32.31 |
| Total | 100% | 1,077.20 |
Trimmings from spinning and rim cutting are clean aluminium scrap; a good report credits their resale value instead of treating them as a loss.
Machinery for an aluminium utensils plant
Hydraulic deep drawing presses are the largest item in our sample, followed by the anodising plant. Press dies and spinning formers are a separate line because each new utensil size needs its own set.
| Machine | What it does | Sample cost (₹ lakh) |
|---|---|---|
| Hydraulic deep drawing presses | Draw circles into pot and cooker bodies | 78.16 |
| Spinning and trimming lathes | Shape the body and trim the rim | 39.08 |
| Annealing furnace | Softens circles and part-drawn bodies | 22.33 |
| Buffing and polishing machines | Give the bright mirror or satin finish | 33.49 |
| Anodising plant with rectifier | Builds the hard oxide layer on the anodised range | 44.66 |
| Beading, curling and riveting machines | Strengthen rims and fix handles | 16.75 |
| Press dies and spinning formers | One set per utensil size and shape | 27.91 |
| Testing equipment and air compressor | Thickness and weight checks; plant air | 16.75 |
| Total plant and machinery | 279.13 | |
Costs are the sample report's estimates for a 1,700 kg per day plant. Get current quotations before you finalise.
Manpower and power for a utensils plant
Spinning and buffing are skill-based jobs, so wages matter more here than in an automated metal plant. Our sample employs 41 people. Power and fuel, mainly for presses, the annealing furnace and the anodising rectifier, take 7.4% of sales.
| Category | Number | Monthly wage (₹) | Year 1 (₹ lakh) |
|---|---|---|---|
| Management, supervision and administration | 6 | 30,500 | 21.96 |
| Skilled workers and operators | 14 | 19,500 | 32.76 |
| Semi-skilled and unskilled workers | 21 | 13,000 | 32.76 |
| Total | 41 | 87.48 |
Wages are assumed to rise 5% a year in the sample. Rates differ by state and cluster.
Licences and ISI mark for aluminium utensils
The BIS licence is the approval that decides when you can start selling, so apply for it as soon as the plant and test equipment are in place.
| BIS licence and ISI mark | Mandatory for wrought aluminium utensils to IS 1660; applies to all units including micro and small enterprises under the DPIIT order of October 2026 |
|---|---|
| Raw material standard | IS 21 for utensil-grade aluminium, listed by BIS for a Quality Control Order from 1 December 2026 |
| Pollution board consent | Utensils pressed from circles by dry mechanical operation are on the green list; acid cleaning and anodising produce effluent, so confirm the category with your State Pollution Control Board |
| GST | HSN 7615, 5% as of October 2026 |
| Business registration | Udyam (MSME) registration and GST registration |
| Factory and safety | Factory licence where worker thresholds apply, fire NOC and an industrial power connection for the press and furnace load |
Market for aluminium utensils in India
Aluminium is still the everyday cooking metal in many Indian homes because it heats fast and costs less than steel or copper. Bulk demand comes from hotels, caterers, langars and institutional kitchens that buy large patilas and degchis by weight.
Most of the trade runs through utensil wholesalers in clusters such as Kanpur Dehat, where the Uttar Pradesh government lists aluminium utensils as the district's ODOP product.
- Utensil wholesalers and distributors
- Hotels, caterers and restaurants
- Institutional and government kitchens
- Kitchenware retail chains
- Pressure cooker and cookware brands buying bodies
Where a new plant wins: mandatory ISI marking shuts out unlicensed workshops that sell thin, scrap-based vessels. A licensed unit with consistent gauge can supply retail chains and brands that need certified products.
Mistakes that weaken an aluminium utensils project report
- Pricing by the piece without weights
Utensils trade by the kilo; revenue must come from output in kg and the price per kg, or sales look higher than they are.
- Ignoring trimming scrap and rejects
Rim trimming, cracks at the draw and buffing losses reduce saleable weight; the report must show yield and the scrap credit.
- Budgeting circles from mixed scrap
BIS has studied the composition of utensils because many secondary makers use scrap; off-grade metal risks failing IS 1660 tests and losing the licence.
- Leaving out dies for every size
Each new pot size needs a die and former; a range of 20 sizes needs far more tooling than one demo set.
- No time for the BIS licence
Sales cannot start until the licence is granted, so the implementation schedule and Year 1 cash flow must allow for it.
How NPCS helps you set up an aluminium utensils plant
- Product range and capacityChoose the mix of plain, anodised and cooker bodies, and the daily output in kg.
- Press shop and finishing lineSize presses, spinning lathes, buffing and anodising, and compare quotations.
- Bank-ready project reportProjections, DSCR, working capital and scrap credit in your lender's format.
- ISI licence and approvalsPlan testing equipment, the BIS licence and state approvals into the schedule.
NPCS, led by founder Ajay Kumar Gupta, has prepared project reports for metal products units since 1994. Its published client list shows 116 assignments in this sector.
What's inside the aluminium utensils sample report
- Introduction
- Uses and applications
- Market potential
- Manufacturing process
- Raw materials
- Plant and machinery
- Land, building and utilities
- Manpower
- Licences and approvals
- Project cost and means of finance
- Working capital
- Projected profitability
- Cash flow statement
- Projected balance sheet
- Depreciation
- Term loan repayment
- Debt service coverage
- Break-even analysis
- Financial ratios
- Key assumptions
- Conclusion
- Monthly loan repayment schedule
18 pages, five-year projections, illustrative figures.
Open sample reportFree sample or a report for your project?
| What you get | Free sample | NPCS report for your project |
|---|---|---|
| Capacity and location | Typical unit | Your capacity, site and state |
| Figures | Illustrative | Built on current prices and quotations |
| Machinery suppliers and quotations | No | Yes |
| Market survey for your region | No | Yes |
| Bank or scheme format (PMEGP, term loan) | No | Yes |
| Use for a loan application | No | Yes |
Real NPCS aluminium utensils project reports
These are aluminium utensils project reports NPCS has prepared, with the plant capacity, total capital investment, rate of return and break-even worked out in each. Costs have moved since some were written, so we bring any of them up to date for your capacity and location.
| Project report | Plant capacity | Total investment | Rate of return | Break-even | Action |
|---|---|---|---|---|---|
| Aluminium House Hold Utensils | 900 MT/Annum | ₹1.46 crore | 43% | 65% | Get this report |
| Aluminium Utensils | 2.00 MT / Day | ₹2.51 crore | 50% | 30% | Get this report |
Figures as worked out in each NPCS report. Total investment includes plant and machinery, land and building, and working capital.
What clients say about NPCS
4.7
264 Google reviews, as of 20 Oct 2026
Clients most often mention
- feasibility reports 18
- project report 16
- helpful for startups 15
- detailed reports 8
-
Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.
Piyush Singh, Google review, 2026
-
Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended
Saroj Yadav, Google review, 2026 View on Google
-
In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.
Shrishti Gautam, Google review, 2026
-
NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.
Raj Yadav, Google review, 2026
Aluminium Utensils project report: frequently asked questions
How much does it cost to start an aluminium utensils factory?
It depends on output and how much you do in-house. A Uttar Pradesh ODOP model report costs a 250 pieces a day workshop at ₹12.39 lakh. A mid-size press shop of 500–1,000 kg per day needs roughly ₹1.5–3 crore. Our sample report models a 1,700 kg per day plant at ₹583 lakh including land, building and working capital margin. Mid-size figures are indicative.
Which aluminium is used to make utensils?
Utensils are drawn from soft, high-purity wrought aluminium circles of the utensil grades in IS 21, which IS 1660 refers to for chemical composition. The grade and temper decide how deep a circle can be drawn without cracking. Circles made from mixed scrap of unknown composition are the main reason utensils fail BIS tests.
Is ISI mark mandatory for aluminium utensils?
Yes. Wrought aluminium utensils come under mandatory BIS certification to IS 1660. A DPIIT Quality Control Order notified in October 2026 applies it with immediate effect to all units, including micro and small enterprises. You need a BIS licence before you sell. Utensils made only for export are outside the order.
Is aluminium utensils manufacturing profitable?
In our illustrative sample, a 1,700 kg per day plant earns an 18% return on investment in Year 3. It breaks even at 44% of capacity and pays back in about 4 years. Margins are thin per kilo, so profit depends on circle buying, scrap recovery, the mix of plain and anodised products and dealer credit.
Aluminium bartan ka business kaise shuru kare?
Start by choosing the product range, such as patilas, kadais or cooker bodies, and the daily output. Then fix the site, buy presses, spinning lathes and buffing machines, and apply for Udyam, GST, pollution consent and a BIS licence for the ISI mark. A project report with costs and projections is needed for the bank loan.
What is the GST rate on aluminium utensils?
Table, kitchen and other household articles of aluminium under HSN 7615 attract 5% GST under the rate schedule notified by CBIC in September 2025, as of October 2026. Aluminium circles bought as raw material carry their own rate, so the project report should treat input tax credit correctly in the working capital.
Is the aluminium utensils project report PDF free, and can I use it for a loan?
The sample is free to view and download. It is an illustrative report that shows the format and depth of an NPCS report. Its figures are representative, not from a real project, so do not submit it to a bank. For a loan, NPCS prepares a report for your own capacity, location and product mix.
Sources and references
- Conformity to BIS mandatory for stainless steel and aluminium utensils (IS 1660)Bureau of Indian Standards, checked Oct 2026
- Upcoming QCOs notified and due for implementation (IS 21 for utensil aluminium)Bureau of Indian Standards, checked Oct 2026
- IS 21:1992 Wrought aluminium and aluminium alloys for manufacture of utensilsBureau of Indian Standards, checked Oct 2026
- Terms of reference: chemical composition of aluminium utensils in the Indian marketBureau of Indian Standards, checked Oct 2026
- Notification No. 9/2025-Integrated Tax (Rate)Central Board of Indirect Taxes and Customs, checked Oct 2026
- Green category industries listPunjab Pollution Control Board, checked Oct 2026
- ODOP Kanpur Dehat: aluminium utensils manufacturing unit, model project reportOne District One Product, Government of Uttar Pradesh, checked Oct 2026
