What is a cold rolled sheet mill project report?
A cold rolled sheet mill project report is a detailed project report (DPR) for a plant that pickles hot rolled steel coil and rolls it to thin gauge. It covers annealing, skin passing, machinery, raw materials, project cost, means of finance, five-year projections, DSCR and break-even, in the form a lender checks.
Steel re-rollers, tube and auto component makers adding a cold rolling line, and their banks use it to size the mill and test whether it can repay a term loan.
Also known as: cold rolling mill project report, CRCA sheet plant project report, cold rolled steel sheet DPR, cold rolled coil plant business plan.
Cold rolled sheet mill plant cost in India: sample economics
Our sample report models an 18 MT per day mill running 330 days a year, or 5,940 MT per year at full capacity. It starts at 60% utilisation and reaches 80% in Year 5, selling at ₹62,900 per MT before GST.
The margin is narrow. Raw materials take 70.8% of sales and net profit is 4.8% of sales in Year 3, so small changes in coil price or yield move the result a lot.
| Land and site development | 55.57 |
|---|---|
| Building and civil works | 215.09 |
| Plant and machinery | 385.61 |
| Other fixed assets | 41.03 |
| Contingencies | 30.04 |
| Preliminary and pre-operative | 18.18 |
| Working capital margin | 94.43 |
| Total | 839.95 |
| Promoter's contribution (25%) | 209.99 |
|---|---|
| Term loan from bank (75%) | 629.96 |
| Cash credit limit (separate) | 283.30 |
| Total project cost | 839.95 |
Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments. Lowest DSCR is 1.25, in Year 2. All figures are illustrative.
Cold rolled sheet mill manufacturing process
Cold rolling turns hot rolled coil, usually 1.6–4 mm thick with a scaled surface, into thinner sheet with a smooth finish and close thickness tolerance. The line below is the one costed in our sample report.
- Coil inspection
Incoming HR coils are checked for grade, thickness, width and edge cracks, because defects in the hot band carry through to the finished sheet.
- Pickling
The coil is uncoiled and run through heated hydrochloric acid tanks that dissolve the mill scale, then rinsed, dried and lightly oiled.
- Cold rolling
A 4-Hi reversing mill squeezes the strip back and forth in several passes, with rolling emulsion cooling the rolls, until it reaches the target gauge.
- Cleaning
Rolling oil left on the strip is removed so it does not burn into carbon stains inside the annealing furnace.
- Bell annealing
Stacked coils are heated under a sealed bell in a hydrogen atmosphere, which softens the work-hardened steel without oxidising the surface.
- Skin pass rolling
A light pass of about 1% reduction sets flatness and surface finish and removes the yield point effect that causes stretcher marks when pressing.
- Slitting, cutting and testing
Coils are slit to width or cut to sheets, tested for thickness, hardness and surface, then oiled and packed against rust.
Which rolling and annealing route suits your mill?
Five design choices set most of the project cost and the grades you can sell. Decide them before you ask for machinery quotations.
| Reversing or tandem mill | A single reversing stand rolls one coil in several passes and suits smaller, varied orders. A tandem mill with several stands rolls in one pass and needs far higher, steady volume to pay for itself. |
|---|---|
| 4-Hi or cluster mill | A 4-Hi stand covers most mild steel CR and CRCA gauges. Very thin or hard material, such as stainless or high-carbon strip, needs a 6-Hi or 20-Hi cluster mill with small work rolls. |
| Own pickling or bought pickled coil | An own pickling line lowers coil cost but adds acid handling, fume scrubbing and hazardous waste. Buying hot rolled pickled and oiled (HRPO) coil cuts capital and approvals but narrows your margin. |
| Bell or continuous annealing | Hydrogen bell furnaces suit batch production and deep-drawing grades at modest volume. Continuous annealing lines are faster and more uniform but belong to large integrated mills. |
| Spent acid handling | Small mills usually neutralise spent pickle liquor or send it to authorised recyclers. Acid regeneration recovers the acid but makes sense only at high throughput. |
Our sample report assumes a 4-Hi reversing mill, own push-pull pickling and hydrogen bell annealing.
Raw materials for cold rolled sheets
HR coil decides both cost and quality. Lenders compare the coil price in your report with current market rates, and buyers reject sheet made from coil with the wrong chemistry for drawing.
| Raw material | Share of cost | Year 3 (₹ lakh) |
|---|---|---|
| Hot rolled steel coil | 94% | 1,740.54 |
| Hydrochloric acid for pickling | 2% | 37.04 |
| Rolling oil and emulsion | 2% | 37.03 |
| Hydrogen and nitrogen for annealing | 2% | 37.03 |
| Total | 100% | 1,851.64 |
Year 3 cost at 70% utilisation in our illustrative sample. The sample holds 30 days of raw material stock.
Machinery for a cold rolling mill
The rolling stand is the heart of the plant and the biggest single cost. Ask for automatic gauge control (AGC), because thickness tolerance is the first thing buyers test.
| Machine | What it does | Sample cost (₹ lakh) |
|---|---|---|
| Push-pull pickling line with acid tanks | Removes mill scale from HR coil | 69.41 |
| 4-Hi reversing cold rolling mill with AGC | Reduces strip to the target gauge | 146.53 |
| Hydrogen bell annealing furnaces | Soften rolled coils for forming | 53.98 |
| Skin pass mill | Sets flatness and surface finish | 30.85 |
| Slitting and cut-to-length lines | Cut coils to width and sheet length | 30.85 |
| Roll grinding machine | Regrinds work and backup rolls | 19.28 |
| EOT cranes and coil handling | Move coils between lines | 23.14 |
| Acid fume scrubber and effluent treatment | Captures acid fumes, treats rinse water | 11.57 |
| Total plant and machinery | 385.61 | |
Costs are the sample report's estimates for an 18 MT per day line. Get current quotations before you finalise.
Manpower and power for a cold rolled sheet mill
Power and fuel cost ₹157.03 lakh in Year 3 of our sample report, or 6% of sales. The mill motors, pickling tank heating and annealing furnaces are the main loads, so the sanctioned power load and tariff need to be in the report from the start.
The sample plant runs with 65 people. Mill operators and roll grinders are the hardest posts to fill and are usually hired from existing re-rolling clusters.
| Category | Number | Monthly wage (₹) | Year 1 (₹ lakh) |
|---|---|---|---|
| Management, supervision and administration | 10 | 30,500 | 36.60 |
| Skilled workers and operators | 23 | 19,500 | 53.82 |
| Semi-skilled and unskilled workers | 32 | 13,000 | 49.92 |
| Total | 65 | 140.34 |
Wages are assumed to rise 5% a year in the sample. All figures are illustrative.
BIS licence and approvals for a cold rolled sheet mill
Cold reduced carbon steel sheet and strip falls under the Steel Quality Control Order. Plan the BIS licence before the first coil is sold.
| Product standard and BIS mark | IS 513 (Part 1) for cold forming and drawing grades and IS 513 (Part 2) for high-tensile grades are listed under the Steel Quality Control Order; sheet without the BIS mark cannot be made or sold |
|---|---|
| Pollution board consent | Consent to establish and consent to operate from the State Pollution Control Board, covering acid fumes, rinse water and the effluent treatment plant |
| Hazardous waste authorisation | Needed for spent pickle liquor, acid sludge and used rolling oil, with disposal through authorised recyclers |
| Factory licence | Under the Factories Act or the state labour code, with approval of the plant layout and crane installations |
| Business registration | Udyam (MSME) registration and GST registration |
| Power and fire | High-tension power connection for the connected load, and a fire NOC covering hydrogen storage for the annealing furnaces |
Requirements differ by state. Confirm current rules with BIS, the state pollution board and the factories department.
Who buys cold rolled sheets and coils?
Cold rolled sheet goes into products where finish, flatness and formability matter: car and two-wheeler parts, appliance bodies, steel furniture and precision tubes. Galvanising and colour coating lines also buy full hard CR coil as their feedstock.
Large integrated mills supply most wide coil in standard sizes. A smaller mill wins on narrow widths, thinner or odd gauges, smaller lot sizes and faster delivery to fabricators near the plant.
- Automobile and two-wheeler component makers
- Consumer durable and appliance manufacturers
- Steel furniture and electrical panel fabricators
- Precision tube and drum makers
- Steel service centres and stockists
Price the spread, not the sheet: buyers track HR coil prices closely, so a mill earns its margin from the gap between HR coil and CR sheet. Your report should show what happens to profit and DSCR when that gap narrows.
Mistakes that weaken a cold rolled sheet mill project report
- Assuming every tonne of coil becomes sheet
Scale removed in pickling, crop ends, edge trim and rejected coils all lose weight. Sales volume must be worked out after these losses.
- Leaving out roll costs
Work rolls wear and are reground often, and backup rolls are replaced over the years. Rolls and grinding belong in running costs, not only in capital cost.
- Using one price for all grades
Full hard, CRCA and deep-drawing grades sell at different prices. A report that applies the best price to all output overstates revenue.
- Under-sizing acid and effluent handling
A scrubber or ETP that is too small delays pollution consent and can stop the pickling line after start-up.
- Thin working capital
Coil is bought against advance or short credit, while buyers take 45 days or more. Without enough cash credit, the mill runs below capacity in its first year.
How NPCS helps you plan a cold rolled sheet mill
- Product mix and mill sizeChoose widths, gauges and CR or CRCA grades to suit your buyers and budget.
- Route and machineryCompare reversing mills, pickling options and annealing furnaces, with supplier quotations.
- Bank-ready project reportProjections, DSCR, working capital and a coil-spread sensitivity in the format your lender wants.
- Approvals and layoutPlant layout, power load, BIS licence and pollution approvals for your state.
NPCS's client list records 2 assignments for cold rolled sheet mills and 116 across metal products, and NPCS has prepared project reports and feasibility studies for steel units since 1994.
What's inside the cold rolled sheet mill sample report
- Introduction
- Uses and applications
- Market potential
- Manufacturing process
- Raw materials
- Plant and machinery
- Land, building and utilities
- Manpower
- Licences and approvals
- Project cost and means of finance
- Working capital
- Projected profitability
- Cash flow statement
- Projected balance sheet
- Depreciation
- Term loan repayment
- Debt service coverage
- Break-even analysis
- Financial ratios
- Key assumptions
- Conclusion
- Monthly loan repayment schedule
19 pages, five-year projections, illustrative figures.
Open sample reportFree sample or a report for your project?
| What you get | Free sample | NPCS report for your project |
|---|---|---|
| Capacity and location | Typical unit | Your capacity, site and state |
| Figures | Illustrative | Built on current prices and quotations |
| Machinery suppliers and quotations | No | Yes |
| Market survey for your region | No | Yes |
| Bank or scheme format (PMEGP, term loan) | No | Yes |
| Use for a loan application | No | Yes |
Real NPCS cold rolled sheet mill project reports
These are cold rolled sheet mill project reports NPCS has prepared, with the plant capacity, total capital investment, rate of return and break-even worked out in each. Costs have moved since some were written, so we bring any of them up to date for your capacity and location.
| Project report | Plant capacity | Total investment | Rate of return | Break-even | Action |
|---|---|---|---|---|---|
| Cold Rolled Sheet Mill | CRC Sheet :150 MT/Day , Galvanised Plane Sheet:66 MT/Day , Galvanised Corrugated Sheet :66 MT/Day , M.S. Pipe & Tubes:100 MT/Day , M.S. Wire… | ₹38.33 crore | 26.8% | 50.7% | Get this report |
Figures as worked out in each NPCS report. Total investment includes plant and machinery, land and building, and working capital.
What clients say about NPCS
4.7
264 Google reviews, as of 20 Oct 2026
Clients most often mention
- feasibility reports 18
- project report 16
- helpful for startups 15
- detailed reports 8
-
Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.
Piyush Singh, Google review, 2026
-
Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended
Saroj Yadav, Google review, 2026 View on Google
-
In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.
Shrishti Gautam, Google review, 2026
-
NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.
Raj Yadav, Google review, 2026
Cold Rolled Sheet Mill project report: frequently asked questions
How much does it cost to set up a cold rolled sheet mill in India?
A compact single-stand mill making narrow strip and sheet at 15–30 MT per day typically needs ₹8–20 crore, including land, building and working capital margin. Our sample report models an 18 MT per day unit at ₹839.95 lakh. Wide-coil mills with their own acid regeneration and continuous annealing run to hundreds of crores. These ranges are indicative; your report costs your own capacity and location.
What is the raw material for cold rolled sheets?
Hot rolled (HR) steel coil is the main input. In our sample report it is 94% of raw material cost, and raw materials as a whole are 70.8% of sales. Hydrochloric acid for pickling, rolling oil and emulsion, and hydrogen and nitrogen for annealing make up the rest. Coil grade and thickness must match the final CR grade you plan to sell.
What is the difference between CR and CRCA sheets?
CR means cold rolled: steel reduced in thickness at room temperature, which leaves it hard and springy. CRCA means cold rolled closed annealed: the same sheet after annealing in a sealed bell furnace, which softens it for bending and deep drawing. Most buyers of furniture, panels and pressed parts ask for CRCA, so a mill without annealing serves a narrower market.
Which machines are needed in a cold rolling mill?
The core line is a pickling line with acid tanks, a 4-Hi reversing cold rolling mill with automatic gauge control, hydrogen bell annealing furnaces and a skin pass mill. Finishing needs slitting and cut-to-length lines, a roll grinder, EOT cranes and an acid fume scrubber with effluent treatment. In our sample report the rolling mill is the largest single machinery item.
Is BIS certification mandatory for cold rolled steel sheets?
Yes, for products covered by the Steel Quality Control Order. The Ministry of Steel lists IS 513 (Part 1 and Part 2), cold reduced carbon steel sheet and strip, under the order. Listed products cannot be made or sold without the BIS mark. Check the current notification and your exact grade with BIS before you plan the product mix.
Is a cold rolled sheet mill profitable?
It can be, but margins are thin and depend on the gap between HR coil and CR sheet prices. Our illustrative sample earns a 15% return on investment in Year 3, with net profit at 4.8% of sales, break-even at 48% of capacity and average DSCR of 1.44. Coil buying, yield and power cost decide most of the result.
Is the sample report free and can I use it for a loan?
The sample is free to view and download. It shows the format and depth of an NPCS report. Its figures are illustrative and not based on a real project, so it should not be submitted to a bank. For a loan, NPCS prepares a report for your own mill size, product mix, location and lender.
Sources and references
- Lok Sabha Unstarred Question No. 3149: steel products under the Steel Quality Control Orders (answered 6 August 2018)Ministry of Steel, Government of India, checked Oct 2026
