What is a water based acrylic adhesive project report?
A water based acrylic adhesive project report is a detailed project report (DPR) for a unit that polymerises acrylate monomers in water to make a milky emulsion adhesive for labels, tapes and films. It sets out the process, reactor and machinery, monomer costs, market, project cost, loan structure, five-year projections, DSCR and break-even.
Promoters use it to size the reactor and apply for a term loan; bank credit officers use it to judge whether the unit can repay.
Also known as: acrylic emulsion adhesive, waterborne acrylic adhesive.
What a bank checks in an acrylic adhesive project report
A credit officer reads an acrylic adhesive report for four numbers first, because monomer prices and buyer credit decide whether the unit repays. These are the values in our sample report.
Acrylate monomers are bought at prices that follow crude and propylene. A report showing a much lower share is overstating the margin.
One monomer drives half the bill. The report should test a 10% rise in its price against profit and the debt service coverage ratio (DSCR).
This is the price of wet emulsion, about half of which is water. Banks compare it with what label and tape makers pay for the same solids content.
Label coaters and tape makers buy on credit. Debtor days, with a month of monomer stock, set the cash credit limit.
Values are the assumptions in our illustrative sample. Your report uses figures for your capacity, suppliers and buyers.
Acrylic adhesive manufacturing plant cost in India
The biggest decision is whether you polymerise monomers yourself or buy base emulsion and compound it. Reactor size then sets the cost. The third tier is the unit in our sample report; the other two are indicative ranges.
Compounding unit
₹40–90 lakh
About 1–2 MT per day, blending bought emulsion
- Mixers, filter and filling₹10–25 lakh
- Shed and fit-out (or rent)₹10–30 lakh
- Working capital margin₹10–25 lakh
Fits PMEGP up to ₹50 lakh, subject to limits
Small reactor plant
₹2.5–4.5 crore
About 1.5–2.5 MT per day, one reactor
- Machinery₹1–2 crore
- Land and building₹1–2 crore
- Working capital margin₹20–40 lakh
MSME term loan, often with CGTMSE cover
Medium plant
₹775 lakh
4,400 kg per day, 14,52,000 kg per year
- Plant and machinery₹354 lakh
- Land and building₹267 lakh
- Working capital margin₹53 lakh
Term loan ₹581 lakh (75%), promoter ₹194 lakh
The first two ranges are indicative. Costs move with reactor size, stainless steel grade, automation and land rates in your area.
Plant economics in our water based acrylic adhesive project report
The sample models a 4,400 kg per day plant working 330 days a year. It starts at 60% of capacity and reaches 80% in Year 5, selling at ₹159 per kg, with 34 people on the payroll.
| Land and site development | 55.59 |
|---|---|
| Building and civil works | 211.66 |
| Plant and machinery | 354.06 |
| Other fixed assets | 54.84 |
| Contingencies | 28.29 |
| Preliminary and pre-operative | 17.61 |
| Working capital margin | 52.74 |
| Total | 774.79 |
| Promoter's contribution (25%) | 193.70 |
|---|---|
| Term loan from bank (75%) | 581.09 |
| Cash credit limit (separate) | 158.22 |
| Total project cost | 774.79 |
Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments; the lowest yearly DSCR is 1.71. All figures are illustrative.
Water based acrylic adhesive manufacturing process
The adhesive is made by semi-continuous emulsion polymerisation: monomers are fed slowly into hot water with an initiator, and each droplet becomes a tiny polymer particle. A typical batch finishes at about 50–55% solids.
- Pre-emulsion
Butyl acrylate, 2-ethylhexyl acrylate, a little acrylic acid and emulsifier are stirred into water until the mix is milky and does not separate.
- Reactor charge
Water, a buffer and some emulsifier are heated in the jacketed reactor under nitrogen, then the persulfate initiator is added.
- Polymerisation
The pre-emulsion is fed over about three to four hours at roughly 80–88 °C. The reaction gives off heat, so the cooling system decides how fast you can feed.
- Residual monomer chase
A second, smaller dose of initiator converts leftover monomer, which lowers odour and keeps the film from staying soft.
- Cooling and neutralising
The batch is cooled and ammonia brings the pH to about 7–8, which stabilises the emulsion in storage.
- Filtration and testing
Bag filters remove grit and coagulum. Each batch is checked for solids, viscosity, pH, peel, loop tack and shear.
- Filling
Approved adhesive goes into HDPE drums and cans. It must be kept above freezing, because frozen emulsion breaks and cannot be recovered.
Raw materials for water based acrylic adhesive
Butyl acrylate is made in India and also imported, and its price moves with crude oil and propylene. Most units hold about a month of monomer stock and buy from at least two sources. The balance between butyl acrylate and 2-ethylhexyl acrylate sets the tack and peel of each grade.
| Raw material | Share of cost | Year 3 (₹ lakh) |
|---|---|---|
| Butyl acrylate monomer | 52% | 470.64 |
| 2-Ethylhexyl acrylate monomer | 26% | 235.32 |
| Acrylic acid and functional monomers | 8% | 72.41 |
| Emulsifiers and initiator | 8% | 72.40 |
| Ammonia, defoamer and biocide | 6% | 54.30 |
| Total | 100% | 905.07 |
Machinery for an acrylic emulsion adhesive plant
The reactor is the largest single item in our sample, and its heat-removal capacity sets the real output of the plant.
| Machine | What it does | Sample cost (₹ lakh) |
|---|---|---|
| SS jacketed reactor with agitator | Polymerises the monomer feed | 106.22 |
| Pre-emulsion tank with stirrer | Makes the monomer emulsion fed to the reactor | 35.41 |
| Monomer tanks and dosing pumps | Store monomers and meter the feed | 42.49 |
| Reflux condenser and nitrogen system | Returns vapour and keeps oxygen out | 21.24 |
| Hot water system and cooling tower | Heats the batch, then removes reaction heat | 42.49 |
| Bag filter and product tanks | Removes coagulum and holds approved batches | 35.41 |
| Drum and can filling machine | Fills by weight for dispatch | 28.32 |
| Laboratory with viscometer and peel tester | Tests every batch before release | 24.78 |
| Pumps, piping and electrical panel | Transfers and controls | 17.70 |
| Total plant and machinery | 354.06 | |
Costs are the sample report's estimates for a 4,400 kg per day plant. Get current quotations before you finalise.
Who buys water based acrylic adhesive in India
Demand comes from converters who coat the adhesive on paper or film and sell it on as labels, tapes and protective films. Packaged food, beverages, pharmaceuticals, e-commerce shipping and consumer goods all need these products, so orders are steady through the year.
Buyers are moving from solvent based grades to water based ones. There is no flammable solvent on the coating line, the film is clear and does not yellow, and odour is low.
- Self-adhesive label stock coaters
- BOPP, masking and cloth tape manufacturers
- Label and sticker printers
- Surface protection film makers
- Paper and film laminators
- Adhesive traders and distributors
How a new unit gets approved: a coater runs your sample on its own line before placing an order. Plan for trial batches, a technical person who can visit the buyer's plant, and two or three grades tuned for paper labels, film labels and tape.
Licences, approvals and GST for an acrylic adhesive unit
Acrylate monomers are flammable liquids, so storage and fire approvals matter more here than in most small chemical units. Rules vary by state; the points below were checked in October 2026.
| Business registration | Udyam (MSME) registration and GST registration |
|---|---|
| Pollution board consent | Consent to establish and operate from the State Pollution Control Board. Synthetic resins are Orange category in the CPCB list revised in 2016; confirm how your board classifies acrylic emulsion |
| Monomer storage | Butyl acrylate has a flash point of about 40 °C (class B). A PESO licence under the Petroleum Rules is needed once storage exceeds the exempt quantity |
| Fire and factory | Fire NOC for the storage and process area, and factory licence where worker and power thresholds apply |
| GST and HSN | Heading 3506 (acrylic adhesives under 3506 91) at 18% IGST, as per Notification No. 9/2025-Integrated Tax (Rate) |
| Quality reference | IS 8402 sets test methods for pressure sensitive adhesive tapes. It is voluntary, and the BIS listing shows no Quality Control Order for it |
Mistakes that weaken an acrylic adhesive project report
- Pricing on solids but selling wet emulsion
Output and price must use the same basis. Mixing per-kg dry polymer costs with per-kg emulsion prices makes the margin look far better than it is.
- Assuming every batch passes
Coagulum, off-spec viscosity and filter losses happen, mostly in the first year. A report with no allowance for rejected or reworked batches overstates saleable output.
- Sizing output on reactor volume alone
Feed time is limited by how much heat the jacket and cooling tower can remove. If cooling is undersized, the plant makes fewer batches a day than the report claims.
- No test for monomer price swings
Butyl acrylate prices can move sharply within a quarter. Without a sensitivity table, the lender cannot see whether DSCR holds when monomer costs rise.
How NPCS helps you set up an acrylic adhesive plant
- Grades and capacityChoose label, tape and film grades and a batch size that suit your buyers and budget.
- Reactor and utilitiesSize the reactor, cooling and monomer storage, and compare equipment quotations.
- Bank-ready project reportProjections, DSCR, monomer price sensitivity and working capital in your lender's format.
- Approvals and layoutPlant layout with a separate monomer store, and the pollution, PESO and fire approvals for your state.
NPCS's client list includes 64 assignments for adhesives, resins and polymer projects, prepared since 1994 for entrepreneurs, banks and companies in India and abroad.
What's inside the water based acrylic adhesive sample report
- Introduction
- Uses and applications
- Market potential
- Manufacturing process
- Raw materials
- Plant and machinery
- Land, building and utilities
- Manpower
- Licences and approvals
- Project cost and means of finance
- Working capital
- Projected profitability
- Cash flow statement
- Projected balance sheet
- Depreciation
- Term loan repayment
- Debt service coverage
- Break-even analysis
- Financial ratios
- Key assumptions
- Conclusion
- Monthly loan repayment schedule
19 pages, five-year projections, illustrative figures.
Open sample reportFree sample or a report for your project?
| What you get | Free sample | NPCS report for your project |
|---|---|---|
| Capacity and location | Typical unit | Your capacity, site and state |
| Figures | Illustrative | Built on current prices and quotations |
| Machinery suppliers and quotations | No | Yes |
| Market survey for your region | No | Yes |
| Bank or scheme format (PMEGP, term loan) | No | Yes |
| Use for a loan application | No | Yes |
Real NPCS water based acrylic adhesive project reports
These are water based acrylic adhesive project reports NPCS has prepared, with the plant capacity, total capital investment, rate of return and break-even worked out in each. Costs have moved since some were written, so we bring any of them up to date for your capacity and location.
| Project report | Plant capacity | Total investment | Rate of return | Break-even | Action |
|---|---|---|---|---|---|
| Water Based Acrylic Adhesive | 2000 Kgs./Day | ₹2.51 crore | 29% | 53% | Get this report |
Figures as worked out in each NPCS report. Total investment includes plant and machinery, land and building, and working capital.
What clients say about NPCS
4.7
264 Google reviews, as of 20 Oct 2026
Clients most often mention
- feasibility reports 18
- project report 16
- helpful for startups 15
- detailed reports 8
-
Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.
Piyush Singh, Google review, 2026
-
Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended
Saroj Yadav, Google review, 2026 View on Google
-
In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.
Shrishti Gautam, Google review, 2026
-
NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.
Raj Yadav, Google review, 2026
Water Based Acrylic Adhesive project report: frequently asked questions
What is the cost of an acrylic adhesive manufacturing plant in India?
An indicative range is ₹40–90 lakh for a compounding unit that blends bought emulsion and ₹2.5–4.5 crore for a small reactor plant. A 4–5 tonne per day plant needs about ₹7–8 crore. Our sample report models 4,400 kg per day at ₹775 lakh, including land, building and working capital margin. Your own report prices your capacity and site.
What raw materials are used to make water based acrylic adhesive?
The main inputs are butyl acrylate and 2-ethylhexyl acrylate, with a few percent of acrylic acid, emulsifiers, an initiator such as ammonium persulfate, ammonia for pH, defoamer and biocide. Water makes up about half the finished product. In our sample report the two acrylate monomers are 78% of raw material cost.
Is water based acrylic adhesive manufacturing profitable?
In our illustrative sample, a 4,400 kg per day unit earns a 25% return on investment in Year 3. It breaks even at 36% of capacity and pays back in about 3.3 years. Real profit depends on monomer buying prices, batch yield, the grades you sell and how much credit label and tape makers expect.
How is water based acrylic adhesive different from solvent based acrylic adhesive?
Both use acrylic polymers. In a water based adhesive the polymer is dispersed in water as fine particles, so there is no flammable solvent on the buyer's coating line and little odour. Solvent based acrylics give higher heat and moisture resistance for some tapes but need solvent handling and recovery. Many label coaters now run water based grades.
Can I get a PMEGP or bank loan for an acrylic adhesive unit?
PMEGP covers manufacturing projects up to ₹50 lakh, so it fits only a small compounding unit. A reactor plant usually takes an MSME term loan with a cash credit limit, and eligible micro and small units can get CGTMSE guarantee cover up to ₹10 crore. Every lender asks for a project report with projections and DSCR.
What is the HSN code and GST rate for acrylic adhesive?
Prepared adhesives fall under HSN heading 3506, and adhesives based on acrylic polymers sit under subheading 3506 91. Under GST Notification No. 9/2025-Integrated Tax (Rate), heading 3506 carries 18% IGST, as checked in October 2026. Confirm the full 8-digit code with your tax adviser before invoicing.
Is the sample report free and can I use it for a loan?
The sample is free to view and download. It is an illustrative report that shows the format and depth of an NPCS report. Its figures are representative rather than taken from a real project, so it should not be submitted to a bank. For a loan, NPCS prepares a report for your own capacity, location and scheme.
Sources and references
- Notification No. 9/2025-Integrated Tax (Rate), GST rates on goodsCentral Board of Indirect Taxes and Customs, checked Oct 2026
- Prime Minister's Employment Generation Programme (PMEGP) guideDistrict Industries Centre, Ganjam, Government of Odisha, checked Oct 2026
- Credit Guarantee Fund Trust for Micro and Small EnterprisesCGTMSE, checked Oct 2026
- IS 8402:1987 Methods of sampling and test for pressure sensitive adhesive tapesBureau of Indian Standards, checked Oct 2026
- Revised categorisation of industries (CPCB, effective 1 October 2016)Kerala State Industrial Development Corporation, checked Oct 2026
- Butyl acrylate product specificationBharat Petroleum Corporation Limited, checked Oct 2026
- Synthesis and properties of water-based acrylic adhesives for glass bottle labels (Polymers, 2020)PubMed Central, US National Library of Medicine, checked Oct 2026
