What is a polyurethane project report?
A polyurethane project report is a detailed project report (DPR) for a unit that reacts and blends polyols with MDI or TDI to make prepolymers, polyol systems and PU binders. It sets out the process, machinery, raw materials, project cost, means of finance, five-year projections, DSCR and break-even that a bank needs.
Entrepreneurs and chemical traders use it to size a PU systems unit and raise a term loan; lenders use it to judge whether the unit can repay.
Also known as: PU, PUR.
What a bank checks in a polyurethane project report
A credit officer reads a polyurethane report for how exposed the unit is to isocyanate prices and slow-paying buyers. These are the values in our sample report and why each one matters.
A systems unit adds value through formulation, not bulk processing, so most of the selling price is bought-in chemicals. A much lower share usually means prices are overstated.
Isocyanates are the single largest input and their price swings with global supply. The report should show what a rise in MDI price does to profit and DSCR.
Panel makers and foamers expect credit. Trade receivables are the largest current asset in the sample, so debtor days set the size of the cash credit limit.
The debt service coverage ratio (cash available against loan instalments) stays at 1.70 or more in every year; the average is 1.95. Lenders read the weakest year, not only the average.
Values are the assumptions in our illustrative sample. Your report uses figures for your capacity, suppliers and market.
How much does a polyurethane unit cost?
Cost depends mostly on whether you only blend polyol systems and binders or also run a reactor for prepolymers. The large tier is the unit in our sample report; the other two are indicative ranges.
Blending and binder unit
₹50–120 lakh
About 300–800 kg per day, rented shed
- Blending vessels, tanks, filling₹25–60 lakh
- Laboratory and fume extraction₹5–15 lakh
- Working capital margin₹8–20 lakh
Smallest projects may fit PMEGP, subject to limits
Mid-size systems unit
₹1.5–3.5 crore
About 1,000–1,500 kg per day, one reactor
- Plant and machinery₹80–150 lakh
- Land and building₹40–120 lakh
- Working capital margin₹15–30 lakh
MSME term loan with a cash credit limit
Prepolymer and systems unit
₹442 lakh
2,100 kg per day, 6,93,000 kg per year
- Plant and machinery₹210.89 lakh
- Land and building₹145.50 lakh
- Working capital margin₹30.80 lakh
Term loan ₹332 lakh (75%), promoter ₹111 lakh
Smaller ranges are indicative and exclude land unless stated. Costs vary with location, reactor size and how much storage you hold.
Polyurethane plant economics in our sample
The sample models a 2,100 kg per day unit working 330 days a year, starting at 60% of capacity and reaching 80% in Year 5. The average selling price is taken at ₹194 per kg across prepolymers, systems and binders.
| Land and site development | 46.59 |
|---|---|
| Building and civil works | 98.91 |
| Plant and machinery | 210.89 |
| Other fixed assets | 29.74 |
| Contingencies | 15.49 |
| Preliminary and pre-operative | 10.04 |
| Working capital margin | 30.80 |
| Total | 442.46 |
| Promoter's contribution (25%) | 110.62 |
|---|---|
| Term loan from bank (75%) | 331.84 |
| Cash credit limit (separate) | 92.41 |
| Total project cost | 442.46 |
Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments. All figures are illustrative.
Polyurethane manufacturing process
Everything turns on keeping water out. Isocyanate reacts with moisture to form carbon dioxide and urea, so a wet polyol or an open drum ruins a batch.
- Raw material testing
Each lot of polyol is checked for hydroxyl value, moisture and viscosity, and each lot of MDI or TDI for NCO content, before it is released to production.
- Polyol drying
Polyols are heated under vacuum to strip out dissolved water before they meet any isocyanate.
- Prepolymer reaction
Dried polyol is fed into excess MDI or TDI in a jacketed reactor under nitrogen, and the batch is held until titration shows the target NCO content.
- Polyol system blending
For two-component systems, polyols are mixed with catalysts, silicone surfactants, chain extenders and blowing agents to a fixed recipe in high-speed vessels.
- Batch testing
Every batch is tested for NCO content or hydroxyl value, viscosity and a cup foam test that records cream, gel and tack-free times against the customer's specification.
- Filling and sealing
Product goes into dry drums or pails under a nitrogen blanket and is sealed at once, since even a few hours of humid air can skin the surface.
Raw materials for polyurethane systems
MDI and TDI are made by a few large producers or imported, and polyol prices follow the petrochemical cycle. Units usually buy isocyanates in 250 kg drums or bulk tankers and hold about a month of stock.
| Raw material | Share of cost | Year 3 (₹ lakh) |
|---|---|---|
| Polymeric MDI and TDI | 42% | 221.84 |
| Polyether polyols | 38% | 200.71 |
| Polyester polyols | 8% | 42.25 |
| Catalysts, surfactants and additives | 7% | 36.97 |
| Blowing agents and chain extenders | 5% | 26.41 |
| Total | 100% | 528.18 |
Machinery for a polyurethane unit
Most of the equipment is about controlling heat, moisture and fumes. The prepolymer reactor is the largest single item in the sample.
| Machine | What it does | Sample cost (₹ lakh) |
|---|---|---|
| Jacketed SS prepolymer reactor with agitator | Reacts polyol with isocyanate at controlled temperature | 52.72 |
| High-speed polyol blending vessels | Mixes polyol systems to recipe | 31.63 |
| Storage tanks with nitrogen blanketing | Holds polyols and isocyanates away from moist air | 25.31 |
| Thermic fluid heater and chilling plant | Heats the reactor and removes reaction heat | 21.09 |
| Transfer pumps, metering and piping | Moves and doses liquids between tanks | 21.09 |
| Vacuum pump and nitrogen generator | Dries polyols and blankets vessels | 16.87 |
| Drum and pail filling with weighing | Fills and seals finished product | 16.87 |
| Quality control laboratory | NCO titration, viscosity and cup foam tests | 14.76 |
| Fume extraction and scrubber | Captures isocyanate vapour at filling points | 10.55 |
| Total plant and machinery | 210.89 | |
Costs are the sample report's estimates for a 2,100 kg per day unit. Get current quotations before you finalise.
Who buys polyurethane systems in India?
Most converters do not want to handle raw MDI and polyols, store them dry and work out formulations. They buy a ready system matched to their machine and product, and they stay with a supplier whose batches behave the same every time.
- Sandwich panel and cold room makers, for rigid insulation foam
- Mattress, furniture and car seat foamers, for flexible and moulded foam
- Sports flooring and rubber tile contractors, for crumb and EPDM binders
- Footwear sole and cast elastomer moulders
- Adhesive, coating and sealant makers, for prepolymers
- Chemical distributors in cities without a local systems house
Where a new unit wins: technical service. A foamer whose line stops because a batch rises too fast will switch to the supplier who can visit the same day and adjust the catalyst level.
Licences and approvals for a polyurethane unit
Isocyanates are listed hazardous chemicals, so a polyurethane unit carries more safety paperwork than a typical resin blender. As of October 2026 these are the main approvals.
| Business registration | Udyam (MSME) registration and GST registration |
|---|---|
| Pollution board consent | Consent to establish and operate from the State Pollution Control Board. CPCB's 2016 directions list synthetic resins under Red; some state lists place them under Orange, so confirm the category for your process |
| Hazardous chemical rules | MDI and TDI are listed in Schedule 1 of the MSIHC Rules, 1989. Safety data sheets are required, and site notification and safety reports apply above 10 tonnes of TDI or 20 tonnes of MDI stored |
| Factory licence | Under the Factories Act where worker and power thresholds apply; rules vary by state |
| Fire safety | Fire NOC from the local fire authority, needed where flammable blowing agents or solvents are stored |
Mistakes that weaken a polyurethane project report
- Costing MDI at one month's price
Isocyanate prices move sharply. A report built on a low month overstates margin; it should show what a price rise does to DSCR.
- No allowance for rejected batches
Off-spec reactivity or moisture pick-up sends batches back. Saleable output and raw material use should allow for some rework.
- Leaving out the laboratory and chemist
Buyers judge a systems supplier on test data. A report without lab equipment and a qualified chemist looks unrealistic to a lender.
- Sizing storage without the MSIHC limits
Holding more than 10 tonnes of TDI or 20 tonnes of MDI brings extra notification and safety reports. Plan tank sizes and approvals together.
- Ignoring buyer credit
Panel makers and foamers pay late. Without realistic debtor days, the cash credit limit is too small in the first year.
How NPCS helps you set up a polyurethane unit
- Product mix and capacityDecide between rigid systems, flexible systems, binders and prepolymers for your market.
- Reactor and plant sizingSize the reactor, blending vessels, nitrogen and storage to your output and the MSIHC limits.
- Bank-ready project reportProjections, DSCR, MDI price sensitivity and working capital in your lender's format.
- Approvals and layoutPlant layout, pollution consent category and the hazardous chemical approvals for your state.
NPCS's client list includes 3 assignments on polyurethane and 64 in adhesives and resins, prepared by the NPCS project team led by founder Ajay Kumar Gupta.
What's inside the polyurethane sample report
- Introduction
- Uses and applications
- Market potential
- Manufacturing process
- Raw materials
- Plant and machinery
- Land, building and utilities
- Manpower
- Licences and approvals
- Project cost and means of finance
- Working capital
- Projected profitability
- Cash flow statement
- Projected balance sheet
- Depreciation
- Term loan repayment
- Debt service coverage
- Break-even analysis
- Financial ratios
- Key assumptions
- Conclusion
- Monthly loan repayment schedule
18 pages, five-year projections, illustrative figures.
Open sample reportFree sample or a report for your project?
| What you get | Free sample | NPCS report for your project |
|---|---|---|
| Capacity and location | Typical unit | Your capacity, site and state |
| Figures | Illustrative | Built on current prices and quotations |
| Machinery suppliers and quotations | No | Yes |
| Market survey for your region | No | Yes |
| Bank or scheme format (PMEGP, term loan) | No | Yes |
| Use for a loan application | No | Yes |
Real NPCS polyurethane project reports
These are polyurethane project reports NPCS has prepared, with the plant capacity, total capital investment, rate of return and break-even worked out in each. Costs have moved since some were written, so we bring any of them up to date for your capacity and location.
| Project report | Plant capacity | Total investment | Rate of return | Break-even | Action |
|---|---|---|---|---|---|
| Adhesives Based ON Polyurethane | 400 Kg./day | ₹62 lakh | 45% | 41% | Get this report |
| Cross Linked Polyurethane Foam | 100 Kg./Day | ₹72 lakh | 64% | 53% | Get this report |
| Expanded Polyurethane Foam | 240000 Kg./Annum | ₹2.63 crore | 44% | 57% | Get this report |
| Polyurethane Sheets & Pipes | 1440 MT/Annum | ₹4.96 crore | 25% | 58% | Get this report |
| Polyurethane Prepolymer | Polyurethane Prepolymer (HMDI Series), 50,000 MT Per Annum | ₹48.66 crore | 29% | 49% | Get this report |
| Polyurethane Rigid Panel for Cold Rooms and Roofing | 2,500 Sqm. Per Day | ₹103 crore | 33% | 32% | Get this report |
Figures as worked out in each NPCS report. Total investment includes plant and machinery, land and building, and working capital.
What clients say about NPCS
4.7
264 Google reviews, as of 20 Oct 2026
Clients most often mention
- feasibility reports 18
- project report 16
- helpful for startups 15
- detailed reports 8
-
Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.
Piyush Singh, Google review, 2026
-
Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended
Saroj Yadav, Google review, 2026 View on Google
-
In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.
Shrishti Gautam, Google review, 2026
-
NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.
Raj Yadav, Google review, 2026
Polyurethane project report: frequently asked questions
What is the polyurethane manufacturing plant cost in India?
A small blending and binder unit needs roughly ₹50–120 lakh, and a mid-size unit with a prepolymer reactor about ₹1.5–3.5 crore, including working capital margin. Our sample report models a 2,100 kg per day unit at ₹442 lakh. These are indicative figures; your project report works out the cost for your product mix, capacity and location.
What raw materials are used to make polyurethane?
Polyurethane is made by reacting a polyol with an isocyanate. A systems unit buys polyether and polyester polyols, polymeric MDI and TDI, and small amounts of catalysts, surfactants, chain extenders and blowing agents. In our sample report MDI and TDI make up 42% of raw material cost and polyether polyols 38%.
Which machines are needed for a polyurethane unit?
The core item is a jacketed stainless steel reactor with an agitator for prepolymers. Around it you need polyol blending vessels, storage tanks kept under nitrogen, a thermic fluid heater and a chiller. Add a vacuum pump, a nitrogen generator, drum filling with weighing, a fume scrubber and a laboratory for NCO and viscosity tests.
Is polyurethane manufacturing profitable?
In our illustrative sample, a 2,100 kg per day unit selling at ₹194 per kg reaches a 25% return on investment in Year 3. It breaks even at 36% of capacity and pays back in about 3.3 years. Real margins depend on MDI and polyol buying prices, batch rejection rates and how long customers take to pay.
Can I get a PMEGP loan for a polyurethane unit?
Only a small unit fits. PMEGP covers manufacturing projects up to ₹50 lakh, with a margin-money subsidy of 15–35% depending on category and location. A unit with a prepolymer reactor usually costs more and is funded by an MSME term loan with a cash credit limit. Every lender asks for a project report with projections and DSCR.
Polyurethane ka business kaise shuru kare?
Start by choosing what you will sell: rigid foam systems, binders for rubber flooring or prepolymers for adhesives. Then line up MDI and polyol suppliers, a small laboratory and a few trial customers. Register on Udyam, apply for pollution consent and get a project report made for the bank loan before ordering the reactor.
Is the sample report free and can I use it for a loan?
The sample is free to view and download. It is an illustrative report that shows the format and depth of an NPCS report; its figures are representative and not based on a real project, so it should not be submitted to a bank. For a loan, NPCS prepares a report for your own capacity, location and loan scheme.
Sources and references
- The Manufacture, Storage and Import of Hazardous Chemical Rules, 1989Punjab Pollution Control Board, checked Oct 2026
- Directions on categorisation of industries (Red, Orange, Green, White), 7 March 2016Central Pollution Control Board (copy hosted by MSEDCL), checked Oct 2026
- Categorisation of industries into Red, Orange, Green and WhitePollution Control Board, Assam, checked Oct 2026
- Prime Minister's Employment Generation Programme (PMEGP)MSME Department, Government of Uttar Pradesh, checked Oct 2026


