What is a butene-1 project report?
A butene-1 project report is a detailed project report (DPR) for a plant that makes polymer-grade butene-1, the C4 alpha olefin used as a comonomer in LLDPE and HDPE. It covers the process route, feedstock, machinery, approvals, project cost, means of finance, five-year projections, DSCR and break-even that a lender or board needs before funding.
Petrochemical companies, refinery-linked investors and C4 stream processors use it to test a project; banks use it to check whether the plant can repay.
Also known as: 1-butene, but-1-ene, alpha-butylene, 1-butylene.
Butene-1 plant cost and economics
The sample report models a compact recovery unit of 8.6 MT per day, or 2,838 MT per year at full capacity, running 330 days a year. It starts at 60% capacity and reaches 80% in Year 5, with butene-1 priced at ₹1,07,000 per MT before GST.
Plant and machinery is the largest cost head at ₹563.74 lakh, followed by building and civil works at ₹324.83 lakh. The columns, storage bullets and flare need heavy foundations and pipe racks, which is why civil cost runs high for a chemical unit of this size.
| Land and site development | 82.14 |
|---|---|
| Building and civil works | 324.83 |
| Plant and machinery | 563.74 |
| Other fixed assets | 94.15 |
| Contingencies | 44.43 |
| Preliminary and pre-operative | 27.73 |
| Working capital margin | 70.50 |
| Total | 1,207.52 |
| Promoter's contribution (25%) | 301.88 |
|---|---|
| Term loan from bank (75%) | 905.64 |
| Cash credit limit (separate) | 211.48 |
| Total project cost | 1,207.52 |
Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments; lowest yearly DSCR 1.45. All figures are illustrative.
Butene-1 manufacturing process from raffinate-2
The sample unit recovers butene-1 from raffinate-2, the C4 stream left after a cracker or refinery has taken out butadiene and isobutene. Separation happens in seven steps, and most of the plant's energy goes into the two columns.
- Feed receipt
Raffinate-2 arrives by pipeline or pressurised tanker and is held in bullets so the columns get a steady feed.
- Selective hydrogenation
Traces of butadiene react with hydrogen over a palladium catalyst and turn into butenes, so they cannot reach the product.
- Lights removal
The first superfractionation column takes isobutane and other light ends overhead.
- Butene-1 separation
A second tall column lifts butene-1 overhead and leaves normal butane and 2-butenes at the bottom as a return stream.
- Purification
Adsorbent guard beds strip water, oxygenates and sulphur down to parts-per-million levels that polymer catalysts can tolerate.
- Testing and storage
Each lot is checked by gas chromatography for purity and stored as a pressurised liquid.
- Dispatch
Butene-1 leaves in pressurised road tankers or by pipeline to the buyer's polymer plant.
Which process route suits a butene-1 project?
The right route depends on what feed you can secure, not on which technology is newest. Butene-1 boils within about a degree of isobutene, so plain distillation only works once isobutene has been removed upstream.
| Ethylene dimerization | Two ethylene molecules are joined over a homogeneous catalyst. It needs an ethylene supply, so it fits units inside a cracker complex. IndianOil's Panipat unit uses this route. |
|---|---|
| Raffinate-2 superfractionation | Butene-1 is separated from the C4 stream in two tall columns with high reflux. It suits a unit next to a refinery or cracker that sells raffinate-2. This is the route in our sample report. |
| Extractive distillation or adsorption | A solvent or adsorbent helps split close-boiling C4s. These variants can cut column height or energy, at the cost of solvent handling or adsorbent replacement. |
| What decides the choice | Feed availability and price, the butene-1 content of the C4 stream, steam cost for reboilers, and whether a polymer plant nearby will sign a term offtake. |
Feedstock and raw materials for butene-1
Raffinate-2 makes up 90% of raw material cost in the sample, and raw materials are 53.3% of sales. Butene-1 is only part of the C4 stream, so the feed contract must state both the feed price and what the supplier pays for the butane and 2-butene return stream.
| Raw material | Share of cost | Year 3 (₹ lakh) |
|---|---|---|
| Raffinate-2 C4 stream | 90% | 1,019.58 |
| Hydrogen for selective hydrogenation | 3% | 33.99 |
| Hydrogenation catalyst and adsorbents | 4% | 45.31 |
| Process chemicals and nitrogen | 3% | 33.99 |
| Total | 100% | 1,132.87 |
Year 3 purchases in our illustrative sample. Your report uses the volume, composition and price formula in your own supply offer.
Plant and machinery for a butene-1 unit
The superfractionation columns are the biggest single item, at about a third of machinery cost. Their height and tray count follow from the purity target and the butene-1 content of your feed.
| Equipment | What it does | Sample cost (₹ lakh) |
|---|---|---|
| Superfractionation columns with trays | Split butene-1 from close-boiling C4s | 191.67 |
| Selective hydrogenation reactor | Converts trace butadiene to butenes | 56.37 |
| Reboilers, condensers and heat exchangers | Supply the heat and reflux the columns need | 90.20 |
| Pressurised storage bullets | Hold feed and product as liquefied gas | 78.92 |
| Adsorber driers and guard beds | Remove water, oxygenates and sulphur | 33.83 |
| Process pumps and compressors | Move feed, reflux and product | 45.10 |
| DCS and field instrumentation | Controls pressures, levels and column profiles | 39.46 |
| Flare and safety systems | Relieve pressure safely during upsets | 28.19 |
| Total plant and machinery | 563.74 | |
Costs are the sample report's estimates for an 8.6 MT per day unit. Get licensor and fabricator quotations before you finalise.
Licences and approvals for a butene-1 plant
Butene-1 is a flammable gas stored as a pressurised liquid, so safety approvals take longer than for most chemical units. Start them alongside the project report, as of October 2026.
| Pressure vessel storage | Licence from PESO on Form LS-1A under the SMPV(U) Rules 2016 for storing liquefied flammable gas in vessels above 1,000 litres water capacity. The application needs layout drawings, P&ID and site plan; major installations also need HAZOP and risk analysis. |
|---|---|
| Environmental clearance | Petrochemical processing units need prior environmental clearance under the EIA Notification 2006. Confirm the category with the State or central appraisal authority for your site. |
| Pollution board consent | Manufacture of petrochemicals is in the Red category, so consent to establish and consent to operate come from the State Pollution Control Board. |
| Hazardous chemicals | On-site emergency plan and safety reporting under the Manufacture, Storage and Import of Hazardous Chemical Rules where storage crosses threshold quantities. |
| Factory and fire | Factory licence for a hazardous process and fire NOC; rules vary by state. |
| Customs classification | Harmonized System subheading 2901.23 (butene and its isomers), used for GST invoicing and for import and export. |
Butene-1 uses and market in India
Polyethylene plants are the main buyers. Butene-1 controls density in LLDPE and in some HDPE grades, which decides how tough and flexible packaging film and pipe will be. A polymer plant buys on a term contract and qualifies a supplier on purity, consistency and delivery, not on spot price.
- Comonomer for LLDPE and HDPE
- Polybutene-1 resins for pipes and films
- Butylene oxide and butanone synthesis
- Secondary butyl alcohol production
- Valeraldehyde and amyl alcohol manufacture
Supply sits with a few crackers: IndianOil stopped importing butene-1 after commissioning its Panipat dimerization unit in May 2014, and began selling surplus in 2017. A new unit needs an anchor buyer before it needs a bank.
Mistakes that weaken a butene-1 project report
- No firm feed agreement
A report built on a hoped-for raffinate-2 supply cannot be appraised. Lenders want a signed term sheet with volume, composition and price formula.
- Assuming the whole feed becomes product
Only the butene-1 in the stream is recovered. If the return stream price is not settled, the yield and margin are overstated.
- Ignoring isobutene in the feed
Distillation cannot separate isobutene from butene-1. Feed with more isobutene than the buyer's limit gives off-spec product however tall the column.
- Under-costing steam for the reboilers
High-reflux columns use a lot of heat. Power and fuel is 6.2% of sales in the sample; a lower figure needs a cheap steam source to back it.
- Skipping trace-impurity control
Carbon monoxide, water or sulphur at a few ppm poison polymer catalysts and lead to rejected lots. Budget for guard beds and an on-line analyser.
How NPCS helps you plan a butene-1 plant
- Route and capacity studyCompare dimerization and raffinate-2 recovery for your feed, site and target buyers.
- Feed and offtake economicsModel feed price formulas, return stream value and term offtake terms.
- Lender-ready project reportProjections, DSCR, sensitivity and working capital in the format your bank or board wants.
- Approvals roadmapPESO, environmental clearance and pollution consent steps with plant layout inputs.
NPCS's client list records 269 assignments in specialty chemicals. The NPCS project team, led by founder Ajay Kumar Gupta, has prepared reports for chemical and petrochemical projects since 1994.
What's inside the butene-1 sample report
- Introduction
- Uses and applications
- Market potential
- Manufacturing process
- Raw materials
- Plant and machinery
- Land, building and utilities
- Manpower
- Licences and approvals
- Project cost and means of finance
- Working capital
- Projected profitability
- Cash flow statement
- Projected balance sheet
- Depreciation
- Term loan repayment
- Debt service coverage
- Break-even analysis
- Financial ratios
- Key assumptions
- Conclusion
- Monthly loan repayment schedule
19 pages, five-year projections, illustrative figures.
Open sample reportFree sample or a report for your project?
| What you get | Free sample | NPCS report for your project |
|---|---|---|
| Capacity and location | Typical unit | Your capacity, site and state |
| Figures | Illustrative | Built on current prices and quotations |
| Machinery suppliers and quotations | No | Yes |
| Market survey for your region | No | Yes |
| Bank or scheme format (PMEGP, term loan) | No | Yes |
| Use for a loan application | No | Yes |
Find NPCS project reports in your budget
What clients say about NPCS
4.7
264 Google reviews, as of 20 Oct 2026
Clients most often mention
- feasibility reports 18
- project report 16
- helpful for startups 15
- detailed reports 8
-
Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.
Piyush Singh, Google review, 2026
-
Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended
Saroj Yadav, Google review, 2026 View on Google
-
In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.
Shrishti Gautam, Google review, 2026
-
NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.
Raj Yadav, Google review, 2026
Butene-1 project report: frequently asked questions
What is the cost of a butene-1 manufacturing plant in India?
Cost depends mostly on the route and scale. Our sample report models a compact 8.6 MT per day recovery unit at ₹1,208 lakh, with plant and machinery at ₹564 lakh. Cracker-linked dimerization units of 20,000 tonnes a year or more cost many times that. A project report for your site works out the cost from your feed, capacity and utilities.
How is butene-1 manufactured?
Butene-1 is made in two main ways. Ethylene dimerization joins two ethylene molecules over a homogeneous catalyst and suits plants inside an ethylene complex. Recovery from raffinate-2 separates butene-1 from a refinery or cracker C4 stream in tall superfractionation columns after butadiene is hydrogenated and isobutene is removed upstream. Your feed source decides the route.
What is butene-1 used for?
Most butene-1 is used as a comonomer in linear low density polyethylene (LLDPE) and in some HDPE grades, where it controls density and film toughness. Smaller volumes go into polybutene-1 resins for pipes and films, butylene oxide, butanone (MEK), secondary butyl alcohol, and valeraldehyde for amyl alcohol and plasticiser intermediates.
What purity of butene-1 do polyethylene producers need?
Polymer-grade butene-1 is usually sold at 99.5% purity or higher. Buyers also cap trace impurities such as butadiene, carbon monoxide, water, sulphur and oxygenates at parts-per-million levels, because these poison polymerisation catalysts. The buyer's specification sheet sets the exact limits, and a project report should size purification and testing to meet it.
Which licences are needed for a butene-1 plant?
The main one is a PESO licence on Form LS-1A under the SMPV(U) Rules 2016, because butene-1 is stored as a pressurised flammable liquid. You also need prior environmental clearance under the EIA Notification 2006 and Red category consent from the State Pollution Control Board. Factory, fire and hazardous chemical rules apply too, and details vary by state.
Is butene-1 production profitable?
In our illustrative sample, the unit earns an 18.6% return on investment in Year 3 and breaks even at 39.4% of capacity. It pays back in about 3.9 years with an average DSCR of 1.66. Real profit depends on the spread between butene-1 and the raffinate-2 price, the feed contract terms, steam cost and steady offtake by a polymer plant.
Is the butene-1 project report PDF sample free, and can I use it for a loan?
The sample is free to view and download. It is an illustrative report that shows the format and depth of an NPCS report. Its figures are representative and not based on a real project, so it should not be submitted to a bank. For a loan or board approval, NPCS prepares a report for your own feed, capacity and location.
Sources and references
- Refineries: Technology with Ecology (Panipat butene-1 unit)Indian Oil Corporation Limited, checked Oct 2026
- Standard operating procedure for SMPV(U) Rules, 2016Petroleum and Explosives Safety Organisation, checked Oct 2026
- SMPV(U) Rules: frequently asked questionsPetroleum and Explosives Safety Organisation, checked Oct 2026
- List of industries under Red categoryDepartment of Environment and Forest, Government of Assam, checked Oct 2026
- Technical EIA guidance manual for petrochemical based processing industryMinistry of Environment and Forests, Government of India, checked Oct 2026
- Harmonized System heading 29.01: acyclic hydrocarbonsWorld Customs Organization, checked Oct 2026
