What is a upvc profiles for doors and windows project report?
A uPVC profiles for doors and windows project report is a detailed project report (DPR) for a plant that extrudes rigid, lead-free PVC compound into window and door profiles. These are the multi-chamber frame, sash, mullion and bead sections that fabricators weld into finished windows. The report covers formulation, extrusion lines, dies, project cost, means of finance, five-year projections, DSCR and break-even.
Promoters use it to size the extrusion plant and raise a term loan; lenders use it to judge whether the unit can repay from profile sales to fabricators.
Also known as: uPVC profile extrusion project report, uPVC window profile manufacturing business plan, project report on uPVC profiles, DPR for uPVC profile plant.
What a bank checks in a uPVC profiles for doors and windows project report
A credit officer reads a profile extrusion report for resin exposure, die investment and repayment headroom. These are the values in our sample report and why each one gets questioned.
The PVC compound is most of what you sell. A report showing a much lower share is usually pricing resin too cheaply or profiles too high.
Resin prices move with the petrochemical cycle and import parity. Banks expect a sensitivity case where resin rises and selling prices lag by a quarter.
DSCR is the cash available to repay divided by the loan instalments due. Year 2 is tightest because full instalments start once the moratorium ends.
Each profile section needs its own die and calibrator set. Lenders ask which sliding, casement or door series the dies cover and who designed them.
Values are the assumptions in our illustrative sample. Your report uses figures for your capacity, suppliers and market.
How much does a uPVC profile extrusion unit cost?
Cost rises with the number of extrusion lines and, just as much, with the number of profile sections you want to offer. The middle tier is the unit in our sample report; the other two are indicative ranges.
One-line unit
₹1.5–2.5 crore
About 1–1.5 MT per day, one series
- Extruder, dies and downstream₹90–140 lakh
- Shed fit-out (rented shed)₹15–30 lakh
- Working capital margin₹10–20 lakh
MSME term loan, often with CGTMSE cover
Two-series unit
₹458 lakh
2.5 MT per day, 825 MT per year
- Plant and machinery₹234 lakh
- Land and building₹145 lakh
- Working capital margin₹29 lakh
Term loan ₹344 lakh (75%), promoter ₹115 lakh
Multi-line plant
₹8–14 crore
About 6–8 MT per day, 3 or more lines
- Machinery with compounding₹4.5–7 crore
- Land and building₹2–4 crore
- Working capital margin₹0.7–1.2 crore
Term loan, often with CGTMSE cover up to its ceiling
Extrusion is not fabrication: a window fabrication shop buys finished profiles and needs cutting, welding and corner cleaning machines worth a few lakh. This page and the sample cover the plant that makes the profiles, which is a far larger investment.
One-line and multi-line ranges are indicative. Costs vary with die design, line automation, lamination and location.
uPVC profiles for doors and windows plant economics
The sample report models a 2.5 MT per day unit running 330 days a year, starting at 60% capacity and reaching 80% in Year 5. Profiles are sold at ₹1,51,000 per MT, about ₹151 per kg ex-factory, excluding GST.
| Land and site development | 55.73 |
|---|---|
| Building and civil works | 89.71 |
| Plant and machinery | 234.24 |
| Other fixed assets | 22.56 |
| Contingencies | 16.20 |
| Preliminary and pre-operative | 10.46 |
| Working capital margin | 29.14 |
| Total | 458.04 |
| Promoter's contribution (25%) | 114.51 |
|---|---|
| Term loan from bank (75%) | 343.53 |
| Cash credit limit (separate) | 87.43 |
| Total project cost | 458.04 |
Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments. All figures are illustrative.
uPVC profiles for doors and windows manufacturing process
Profiles are made in one continuous line, from powder blend to cut lengths. Output and quality depend on the die and calibrator set more than on the extruder itself.
- Dry blending
Resin and additives are mixed in a hot mixer at about 120°C, then cooled in a cold mixer so the blend flows freely and does not lump.
- Extrusion
A conical twin-screw extruder melts the blend gently and pushes it through a die that forms the multi-chamber section in one pass.
- Vacuum calibration
The soft profile is drawn through vacuum calibrators and water-spray tanks that lock in its outer dimensions as it cools.
- Haul-off and cutting
A caterpillar haul-off pulls the profile at constant speed, and a travelling saw cuts it to lengths of about 6 metres.
- Filming and inspection
Protective film goes on the sight faces, and operators check wall thickness, weight per metre and surface for streaks or sink marks.
- Testing and bundling
Batch samples are tested for heat reversion, impact and welded-corner strength before profiles are bundled and stretch-wrapped.
Raw materials for uPVC window profiles
The formulation decides whether profiles stay white and strong after years in the sun. Rutile titanium dioxide gives UV resistance, and the impact modifier stops profiles cracking when they are cut or screwed in cold weather.
| Raw material | Share of cost | Year 3 (₹ lakh) |
|---|---|---|
| Suspension PVC resin (K-67) | 70% | 357.76 |
| Impact modifier (CPE) | 9% | 46.00 |
| Calcium-zinc stabiliser | 9% | 46.00 |
| Titanium dioxide (rutile) | 6% | 30.66 |
| Lubricants and processing aids | 4% | 20.44 |
| Calcium carbonate filler | 2% | 10.22 |
| Total | 100% | 511.08 |
Calcium-zinc replaces lead stabilisers, which IS 17953 does not allow in window profiles.
Machinery for a uPVC profile extrusion plant
The extruder is the largest single item in the sample, but dies and calibrators come next and are the part most often under-budgeted.
| Machine | What it does | Sample cost (₹ lakh) |
|---|---|---|
| Conical twin-screw profile extruder | Melts and pumps the PVC blend | 79.64 |
| Profile dies and calibrators | Shape each frame, sash and bead section | 51.53 |
| Vacuum calibration and cooling table | Holds dimensions while the profile cools | 23.42 |
| High-speed hot and cold mixer | Prepares the dry blend | 21.08 |
| Haul-off and cutting unit | Pulls and cuts profiles to length | 18.74 |
| Chiller, cooling tower and air compressor | Cooling water and process air | 14.06 |
| Vacuum loaders and material conveying | Moves blend from mixer to extruder | 11.71 |
| Scrap grinder and pulveriser | Turns start-up scrap back into powder | 7.03 |
| Quality testing equipment | Impact, heat reversion and weld tests | 7.03 |
| Total plant and machinery | 234.24 | |
Costs are the sample report's estimates for a 2.5 MT per day unit. Get current quotations before you finalise.
Who buys uPVC profiles, and how a new plant competes
Your customer is the fabricator, not the homeowner. Fabricators cut, weld and glaze profiles into windows for apartments, hotels, hospitals and offices. They buy a complete system of frames, sashes, mullions and glazing beads that fit together.
That makes switching suppliers slow. A fabricator who trusts your dimensions, colour and weld strength tends to stay, and one who gets warped or yellowing profiles rarely returns.
- uPVC window and door fabricators
- Builders and real estate developers
- Architects and facade contractors
- Distributors of window systems
- Government and institutional housing projects
Where a regional plant wins: profiles are bulky for their weight, so freight from a distant brand adds up. A plant that supplies fabricators within a few hundred kilometres, with short lead times on the sections they use most, can compete with larger names.
BIS standard and licences for a uPVC profile unit
IS 17953:2023 is the Indian standard for uPVC window and door profiles. Build your formulation and in-house tests around it from the first trial run.
| Business registration | Udyam (MSME) registration and GST registration |
|---|---|
| Product standard | IS 17953:2023 sets tolerances, mass at least 95% of the declared mass per metre, Vicat softening point of at least 75°C and heat reversion of 2% or less for main profiles |
| Formulation rules | No lead or cadmium based additives; recycled uPVC only in the core, fully covered by a coextruded layer at least 0.5 mm thick on visible faces |
| BIS certification | Compulsory only if a Quality Control Order is notified for the product; check the BIS website before launch |
| Pollution board consent | Consent to establish and operate from the State Pollution Control Board; Punjab's list, for example, places virgin plastic processing in the green category |
| Factory and power | Factory licence where worker thresholds apply, and an industrial power connection for the extruder, mixer and chiller load |
Mistakes that weaken a uPVC profile project report
- Budgeting one die set for a whole range
A sliding series, a casement series and a door series each need several sections, and every section needs its own die and calibrator.
- Ignoring weight per metre
Running heavier than declared gives resin away on every metre, and running below 95% of declared mass fails IS 17953.
- Pricing with a lead stabiliser formulation
Lead-based additives are cheaper but not allowed under IS 17953, so the costing must use calcium-zinc from the start.
- No allowance for start-up scrap
Every die change and start-up makes scrap. Without a grinder and a reuse rule, saleable output is lower than the report claims.
- Treating fabricators as cash buyers
Most fabricators expect credit. The sample assumes 45 days of receivables; leaving this out shrinks the cash credit limit.
How NPCS helps you set up a uPVC profile plant
- Series and capacityChoose the profile series and daily output your fabricator market can absorb.
- Lines, dies and formulationCompare extrusion lines and die sets, and cost a lead-free formulation.
- Bank-ready project reportProjections, DSCR, resin sensitivity and working capital in the format your lender wants.
- Layout and approvalsPlant layout, power load and the approvals list for your state.
NPCS's client list records 62 assignments in plastic moulded and extruded products and 4 for uPVC profiles, and NPCS has prepared project reports for entrepreneurs, banks and companies since 1994.
What's inside the upvc profiles for doors and windows sample report
- Introduction
- Uses and applications
- Market potential
- Manufacturing process
- Raw materials
- Plant and machinery
- Land, building and utilities
- Manpower
- Licences and approvals
- Project cost and means of finance
- Working capital
- Projected profitability
- Cash flow statement
- Projected balance sheet
- Depreciation
- Term loan repayment
- Debt service coverage
- Break-even analysis
- Financial ratios
- Key assumptions
- Conclusion
- Monthly loan repayment schedule
18 pages, five-year projections, illustrative figures.
Open sample reportFree sample or a report for your project?
| What you get | Free sample | NPCS report for your project |
|---|---|---|
| Capacity and location | Typical unit | Your capacity, site and state |
| Figures | Illustrative | Built on current prices and quotations |
| Machinery suppliers and quotations | No | Yes |
| Market survey for your region | No | Yes |
| Bank or scheme format (PMEGP, term loan) | No | Yes |
| Use for a loan application | No | Yes |
Real NPCS upvc profiles for doors and windows project reports
These are upvc profiles for doors and windows project reports NPCS has prepared, with the plant capacity, total capital investment, rate of return and break-even worked out in each. Costs have moved since some were written, so we bring any of them up to date for your capacity and location.
| Project report | Plant capacity | Total investment | Rate of return | Break-even | Action |
|---|---|---|---|---|---|
| Of uPVC Profiles for Doors and Windows | uPVC Profiles 2,000 Kgs Per Day Wood Laminated uPVC Profiles 1,570 Kgs Per Day | ₹24.1 lakh | 26% | 75% | Get this report |
| UPVC Profiles for Doors and Windows | 8.3 MT/Day | ₹6.54 crore | 28% | 57% | Get this report |
| UPVC Profiles for Doors and Windows | 8.3 MT/Day | ₹6.81 crore | 26% | 58% | Get this report |
| UPVC Profiles for Doors and Windows | 8.3 MT/Day | ₹11.19 crore | 26% | 41% | Get this report |
Figures as worked out in each NPCS report. Total investment includes plant and machinery, land and building, and working capital.
What clients say about NPCS
4.7
264 Google reviews, as of 20 Oct 2026
Clients most often mention
- feasibility reports 18
- project report 16
- helpful for startups 15
- detailed reports 8
-
Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.
Piyush Singh, Google review, 2026
-
Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended
Saroj Yadav, Google review, 2026 View on Google
-
In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.
Shrishti Gautam, Google review, 2026
-
NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.
Raj Yadav, Google review, 2026
uPVC Profiles for Doors and Windows project report: frequently asked questions
What is the uPVC profiles for doors and windows manufacturing plant cost in India?
A one-line unit making about 1–1.5 MT per day needs roughly ₹1.5–2.5 crore, and a three-line plant of 6–8 MT per day about ₹8–14 crore. Our sample report models a 2.5 MT per day unit at ₹458 lakh, including land, building and working capital margin. These are indicative figures; the cost for your plant depends on the dies, automation and location you choose.
What raw materials are used to make uPVC window profiles?
Suspension PVC resin is the base, blended with a calcium-zinc stabiliser, an impact modifier such as CPE, rutile titanium dioxide for UV resistance, lubricants and a little calcium carbonate. In our sample report PVC resin is 70% of raw material cost. IS 17953 does not allow lead or cadmium based additives in these profiles.
Is uPVC profile manufacturing profitable?
It can be, at the right scale. In our illustrative sample a 2.5 MT per day unit earns a 14% return on investment in Year 3. It breaks even at 45% of capacity and pays back in about 4.6 years. Margins depend mostly on resin buying, scrap control, weight per metre discipline and how quickly fabricators pay. Treat these as sample figures, not a forecast for your plant.
Is there a BIS standard for uPVC window and door profiles?
Yes. IS 17953:2023 covers uPVC profiles for windows and doors. It sets dimensional tolerances, minimum mass per metre, Vicat softening point, heat reversion, impact, weld strength and colour stability, and bans lead and cadmium based additives. BIS certification becomes compulsory only if a Quality Control Order is notified, so check the BIS site before you launch.
Can I get a PMEGP or Mudra loan for a uPVC profile extrusion unit?
Usually not for the full plant. PMEGP covers manufacturing projects up to ₹50 lakh and Mudra loans go up to ₹20 lakh under Tarun Plus, while even a small extrusion line costs more. Profile plants normally take an MSME term loan, and CGTMSE guarantee cover of up to ₹10 crore can reduce the collateral the bank asks for.
uPVC profile ka business kaise shuru kare?
Start by choosing the profile series you will sell, such as sliding and casement, and the capacity your region can absorb. Then get die and extruder quotations, fix a lead-free formulation, find land with enough power, and prepare a bank-format project report. Line up a few fabricators before production starts, because they are your main buyers.
Is the sample report free and can I use it for a loan?
The sample is free to view and download. It is an illustrative report that shows the format and depth of an NPCS report; its figures are representative and not based on a real project, so it should not be submitted to a bank. For a loan, NPCS prepares a report for your own capacity, location and loan scheme.
Sources and references
- IS 17953:2023 uPVC Profiles for Windows and Doors, SpecificationBureau of Indian Standards, checked Oct 2026
- Prime Minister Employment Generation ProgrammeBank of India, checked Oct 2026
- PMEGP scheme detailsMSME Department, Government of Uttar Pradesh, checked Oct 2026
- Credit Guarantee Fund Trust for Micro and Small EnterprisesCGTMSE, checked Oct 2026
- Mudra loan limit raised to ₹20 lakh (Tarun Plus)Press Information Bureau, Government of India, checked Oct 2026
- Green category industriesPunjab Pollution Control Board, checked Oct 2026
