What is a solid rubber tyres project report?
A solid rubber tyres project report is a detailed project report (DPR) for a unit that moulds rubber compounds into airless tyres for forklifts and industrial machines. It sets out the process, machinery, raw materials, market, project cost, means of finance, five-year projections, DSCR and break-even that a bank needs before funding the plant.
Entrepreneurs and rubber goods makers use it to size the plant and apply for a term loan; lenders use it to check whether the unit can repay from its cash flow.
Also known as: solid tyres, solid rubber tires, solid tires.
What a bank checks in a solid rubber tyres project report
A credit officer reads a solid tyre report for four numbers that show whether the plant can carry its loan. These are the values in our sample report and why each one matters.
Rubber compound is most of the cost of a solid tyre. A report that shows a much lower share is usually pricing compound at last year's rubber rates.
Natural rubber prices swing with the crop and with imports. Lenders expect the report to test a rise in rubber price against profit and DSCR.
Thick tyres stay in heated moulds for long cycles, and the kneader draws heavy load. Fuel for the thermic fluid heater belongs in this line.
Forklift dealers and fleet owners buy on credit. Debtor days, with 30 days of rubber stock, set the cash credit limit the bank must approve.
Values are the assumptions in our illustrative sample. Your report uses figures for your capacity, suppliers and buyers.
Solid rubber tyres manufacturing plant cost in India
Cost depends on whether you mix your own compound, how many curing presses you run and how many tyre sizes you hold moulds for. The middle tier is the unit in our sample report; the other two are indicative ranges.
Small unit
₹50–150 lakh
About 0.2–0.6 MT per day, 3–6 presses
- Machinery and moulds₹30–90 lakh
- Shed and fit-out (or rent)₹10–35 lakh
- Working capital margin₹5–20 lakh
Buys ready compound or uses one mixing mill; PMEGP only within its limit
Mid-size unit
₹437 lakh
1.7 MT per day, 561 MT per year
- Plant and machinery₹223 lakh
- Land and building₹137 lakh
- Working capital margin₹31 lakh
Term loan ₹328 lakh (75%), promoter ₹109 lakh
Large unit
₹10–18 crore
About 4–8 MT per day, internal mixer
- Machinery and moulds₹5–9 crore
- Land and building₹2.5–5 crore
- Working capital margin₹1–2 crore
MSME term loan; suits makers seeking equipment-maker approvals
Small and large ranges are indicative and exclude land unless stated. Costs vary with location, press count, mould range and machine make.
Solid tyre plant economics in the sample report
The sample report models a 1.7 MT per day unit working 330 days a year, starting at 60% capacity and reaching 80% in Year 5. The selling price is taken at ₹2,33,000 per MT ex-GST, averaged across a mix of sizes.
| Land and site development | 50.05 |
|---|---|
| Building and civil works | 87.28 |
| Plant and machinery | 222.55 |
| Other fixed assets | 21.41 |
| Contingencies | 15.49 |
| Preliminary and pre-operative | 9.92 |
| Working capital margin | 30.66 |
| Total | 437.36 |
| Promoter's contribution (25%) | 109.34 |
|---|---|
| Term loan from bank (75%) | 328.02 |
| Cash credit limit (separate) | 91.99 |
| Total project cost | 437.36 |
Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments. All figures are illustrative.
Solid rubber tyres manufacturing process
A solid resilient tyre is built in three layers: a hard base that grips the rim, a soft cushion that absorbs shock, and a wear-resistant tread. Each layer has its own compound, so the process starts with mixing three recipes, not one.
- Compounding
Natural and synthetic rubber are mixed with carbon black, oil and chemicals in a dispersion kneader to make the base, cushion and tread compounds.
- Milling
Each batch is cooled on a two-roll mill, and sulphur and accelerators are added at low temperature so the compound does not start curing early.
- Strip preparation
Compound is extruded or cut into strips and weighed for each size; an underweight tyre fails in the mould and becomes scrap.
- Tyre building
The base compound is laid with steel bead wires, then the cushion and tread are wound on to the set weight.
- Moulding and curing
The green tyre is cured in a heated mould in a hydraulic press; thick sections need long cycles so heat reaches the core.
- Trimming and inspection
Flash is trimmed, and each tyre is checked for weight, hardness, size and bonding between layers.
- Marking and dispatch
Tyres are marked with size and load details and sent to dealers, fleet owners and equipment makers.
Raw materials for solid rubber tyres
Natural rubber in RSS sheet or ISNR block form is the base of every compound. Non-marking tyres for food and pharma warehouses replace carbon black with light-coloured fillers, which changes both cost and recipe.
| Raw material | Share of cost | Year 3 (₹ lakh) |
|---|---|---|
| Natural rubber (RSS and ISNR grades) | 48% | 230.95 |
| Synthetic rubber (SBR and BR) | 14% | 67.36 |
| Carbon black | 20% | 96.23 |
| Fillers, process oil and rubber chemicals | 12% | 57.73 |
| Steel bead wire for tyre bases | 6% | 28.87 |
| Total | 100% | 481.14 |
Machinery for a solid tyre unit
The curing press set is the largest machinery item in the sample, followed by the dispersion kneader. Moulds are a separate and growing cost, because every size and tread pattern needs its own.
| Machine | What it does | Sample cost (₹ lakh) |
|---|---|---|
| Dispersion kneader | Mixes rubber, carbon black and chemicals | 40.06 |
| Two-roll mixing mills | Cool batches and add curatives | 26.71 |
| Strip extruder and cutter | Forms compound into weighed strips | 17.80 |
| Tyre building and winding machine | Builds base, cushion and tread layers | 17.80 |
| Hydraulic curing press set | Holds moulds under heat and pressure | 57.86 |
| Tyre moulds in common sizes | Shape each size and tread pattern | 31.16 |
| Thermic fluid heater | Heats the press platens | 13.35 |
| Trimming and finishing machine | Removes flash after curing | 6.68 |
| Rubber testing laboratory | Checks hardness, cure and compound quality | 11.13 |
| Total plant and machinery | 222.55 | |
Costs are the sample report's estimates for a 1.7 MT per day unit. Get current quotations before you finalise.
Who buys solid rubber tyres in India?
Most demand comes from forklift trucks and other material handling machines in warehouses, factories, ports and logistics parks, where a puncture stops work. Tyres wear out in months on busy shifts, so the replacement market is larger and steadier than supply to new machines.
Three types cover most sales: resilient tyres that fit standard pneumatic rims, press-on bands moulded on a steel ring, and non-marking tyres for clean floors.
- Forklift dealers and service companies
- Warehouses, logistics parks and container terminals
- Factories running their own forklift fleets
- Tyre distributors serving the replacement market
- Makers of forklifts, trolleys and airport ground equipment
Where a new unit wins: fleet buyers want the common sizes, such as 6.50-10 and 18x7-8, delivered within days. A unit that stocks those sizes near an industrial cluster can compete with larger makers on lead time.
Licences, standards and GST for a solid tyre unit
| Business registration | Udyam (MSME) registration and GST registration |
|---|---|
| GST on the product | Solid or cushion tyres under HSN 4012 at 18% (rate notification of 17 September 2025), checked October 2026 |
| Pollution board consent | Consent to establish and operate from the State Pollution Control Board; boards that follow CPCB criteria list tyre vulcanisation under Orange, so confirm the category in your state |
| BIS certification | The tyre Quality Control Order and its standards (IS 15627, IS 15633, IS 15636) cover pneumatic tyres; no BIS standard for solid industrial tyres was found as of October 2026 |
| Size and marking | ISO 10499-1 sets designation, dimensions and marking for solid tyres on pneumatic rims; buyers expect tyres to fit standard rims |
| Factory and safety | Factory licence where the workforce threshold applies, fire NOC and an industrial power connection for the connected load |
Mistakes that weaken a solid tyre project report
- Counting presses without the cure cycle
Output depends on how long each size stays in the mould. Capacity based on press count alone overstates sales.
- Pricing per piece without a size mix
Tyres sell per piece but are costed per kilogram of compound. Without a clear size mix, revenue and raw material cost do not match.
- Leaving out mould costs for new sizes
Each new size or tread needs a mould. A report that budgets only the first set leaves no money to widen the range.
- Ignoring scrap and flash
Trimmed flash and rejected tyres from poor bonding are lost compound. Yield must allow for them.
- Using one rubber price for five years
Natural rubber is nearly half of material cost in the sample. A flat price hides the biggest risk to DSCR.
How NPCS helps you set up a solid tyre unit
- Size range and capacityPick tyre types and sizes to match your buyers, then set press count and output.
- Compounding and machineryCompare kneader, mill and press options and get supplier quotations.
- Bank-ready project reportProjections, DSCR, rubber price sensitivity and working capital in your lender's format.
- Approvals and layoutPlant layout, heater and power load, and the approvals list for your state.
NPCS's client list shows 40 assignments in rubber products, including a detailed project report on solid rubber tyres. NPCS has prepared project reports for entrepreneurs, banks and companies since 1994.
What's inside the solid rubber tyres sample report
- Introduction
- Uses and applications
- Market potential
- Manufacturing process
- Raw materials
- Plant and machinery
- Land, building and utilities
- Manpower
- Licences and approvals
- Project cost and means of finance
- Working capital
- Projected profitability
- Cash flow statement
- Projected balance sheet
- Depreciation
- Term loan repayment
- Debt service coverage
- Break-even analysis
- Financial ratios
- Key assumptions
- Conclusion
- Monthly loan repayment schedule
19 pages, five-year projections, illustrative figures.
Open sample reportFree sample or a report for your project?
| What you get | Free sample | NPCS report for your project |
|---|---|---|
| Capacity and location | Typical unit | Your capacity, site and state |
| Figures | Illustrative | Built on current prices and quotations |
| Machinery suppliers and quotations | No | Yes |
| Market survey for your region | No | Yes |
| Bank or scheme format (PMEGP, term loan) | No | Yes |
| Use for a loan application | No | Yes |
Real NPCS solid rubber tyres project reports
These are solid rubber tyres project reports NPCS has prepared, with the plant capacity, total capital investment, rate of return and break-even worked out in each. Costs have moved since some were written, so we bring any of them up to date for your capacity and location.
| Project report | Plant capacity | Total investment | Rate of return | Break-even | Action |
|---|---|---|---|---|---|
| Solid Rubber Tyres | Truck Tyre, 200 Pcs. Per Day Lorry Tyre, 200 Pcs. Per Day Bike Tyre, 200 Pcs. Per Day Car Tyre, 200 Pcs. Per Day | ₹44.28 crore | 35% | 52% | Get this report |
Figures as worked out in each NPCS report. Total investment includes plant and machinery, land and building, and working capital.
What clients say about NPCS
4.7
264 Google reviews, as of 20 Oct 2026
Clients most often mention
- feasibility reports 18
- project report 16
- helpful for startups 15
- detailed reports 8
-
Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.
Piyush Singh, Google review, 2026
-
Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended
Saroj Yadav, Google review, 2026 View on Google
-
In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.
Shrishti Gautam, Google review, 2026
-
NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.
Raj Yadav, Google review, 2026
Solid Rubber Tyres project report: frequently asked questions
How much does it cost to start a solid tyre manufacturing unit?
A small unit that buys ready compound and runs a few presses needs roughly ₹50–150 lakh. A plant with its own kneader and 1.5–2 MT per day of output needs about ₹4–6 crore. Our sample report models a 1.7 MT per day unit at ₹437 lakh. These are indicative figures; your report works out the cost for your sizes, location and machine makes.
What raw materials are used to make solid rubber tyres?
Natural rubber is the main input, blended with synthetic rubber such as SBR or BR, carbon black, fillers, process oil and curing chemicals. Resilient tyres also need steel bead wire in the base. In our sample report natural rubber is 48% of raw material cost and carbon black 20%, so rubber prices move profit more than any other cost.
What is the difference between solid and pneumatic tyres?
A pneumatic tyre carries the load on compressed air, while a solid tyre carries it on rubber alone, so it cannot puncture or lose pressure. Solid tyres run cooler at low speed, need almost no maintenance and suit forklifts on floors with metal scrap or debris. They give a harder ride and are not made for road speeds.
Is solid tyre manufacturing profitable?
In our illustrative sample, a 1.7 MT per day unit earns a 22% return on investment in Year 3. It breaks even at 40% of capacity and pays back in about 3.5 years. Real profit depends on natural rubber prices, scrap and flash losses, how many sizes you hold moulds for, and the credit that forklift dealers and fleet buyers expect.
Can I get a PMEGP or bank loan for a solid tyre plant?
PMEGP covers manufacturing projects up to ₹50 lakh with a margin-money subsidy, which suits only a very small unit. Most solid tyre plants take an MSME term loan, often with CGTMSE guarantee cover, which now goes up to ₹10 crore for eligible micro and small units. Either way, the lender needs a project report with projections and DSCR.
What is the GST rate on solid rubber tyres?
Solid or cushion tyres of rubber fall under HSN heading 4012 and attract 18% GST under the rate notification of 17 September 2025. Solid tyres for motor vehicles and for other vehicles have separate tariff items under 4012 90. Confirm the rate for your exact item with your tax adviser, because rate schedules are amended from time to time.
Is the solid rubber tyres project report PDF free, and can I use it for a loan?
The sample PDF is free to view and download. It is an illustrative report that shows the format and depth of an NPCS report. Its figures are representative and not based on a real project, so it should not be submitted to a bank. For a loan, NPCS prepares a report for your own capacity, location and loan scheme.
Sources and references
- Notification No. 9/2025-Integrated Tax (Rate), Schedule IICentral Board of Indirect Taxes and Customs, checked Oct 2026
- Indian standards for tyres and wheelsBureau of Indian Standards, checked Oct 2026
- Pneumatic Tyres and Tubes for Automotive Vehicles (Quality Control) Order, WTO notification G/TBT/N/IND/20Centre for WTO Studies, IIFT, checked Oct 2026
- ISO 10499-1:2019 Industrial tyres and rims, rubber solid tyres (metric series) for pneumatic tyre rimsAmerican National Standards Institute webstore, checked Oct 2026
- Categorisation of industrial sectors under Orange as per CPCB criteriaState Pollution Control Board, Odisha, checked Oct 2026
- Prime Minister's Employment Generation Programme (PMEGP) guideDistrict Industries Centre, Ganjam, Government of Odisha, checked Oct 2026
- Credit Guarantee Fund Trust for Micro and Small EnterprisesCGTMSE, checked Oct 2026
