What is a chromite beneficiation project report?
A chromite beneficiation project report is a detailed project report (DPR) for a plant that upgrades low-grade chrome ore and fines to a saleable concentrate of about 50–52% Cr2O3. It covers ore supply, the gravity circuit, tailings and water, approvals, project cost, finance, five-year projections, DSCR and break-even.
Mine owners, ore traders and ferro chrome producers use it to size a plant and raise a term loan; lenders use it to test whether the plant can repay.
Also known as: chrome ore beneficiation, chromite ore beneficiation.
Chromite beneficiation plant cost in India: our sample economics
The sample report models a gravity plant making 25 MT of chrome concentrate a day, or 7,500 MT a year over 300 working days. It starts at 60% capacity and reaches 80% in Year 5, selling concentrate at ₹23,800 per MT before GST.
That price sits close to the Indian Bureau of Mines average sale price of ₹23,131 per tonne for Odisha chromite concentrates in December 2025.
| Land and site development | 55.97 |
|---|---|
| Building and civil works | 129.54 |
| Plant and machinery | 252.02 |
| Other fixed assets | 36.85 |
| Contingencies | 19.08 |
| Preliminary and pre-operative | 12.34 |
| Working capital margin | 40.70 |
| Total | 546.50 |
| Promoter's contribution (25%) | 136.62 |
|---|---|
| Term loan from bank (75%) | 409.88 |
| Cash credit limit (separate) | 122.12 |
| Total project cost | 546.50 |
Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments. Lowest DSCR in the sample is 1.22. All figures are illustrative.
Chromite beneficiation process, step by step
Chromite is heavier than the silicate and iron oxide minerals around it, so most Indian plants separate it by gravity in water. The aim is to free the chromite grains without grinding them so fine that they are lost.
- Ore receipt and blending
Each truck of low-grade ore is weighed and sampled for Cr2O3, then stacked by grade so the plant gets an even feed through the month.
- Crushing and screening
A jaw crusher and a hammer crusher in closed circuit break lumps down to a few millimetres, and screens send oversize back for another pass.
- Regrinding
A rod mill reduces the screen oversize to below about 1 mm; a rod mill is used because it makes fewer slimes than a ball mill.
- Classification and desliming
Hydrocyclones split the slurry by size and remove slimes finer than about 20 microns, which spirals and tables cannot hold.
- Spiral concentration
Rougher spirals make a first concentrate, and scavenger spirals pull back chromite that slipped into the rougher tailings.
- Table cleaning
Wet shaking tables lift the spiral concentrate to about 50–52% Cr2O3 and reject the remaining silica and serpentine.
- Dewatering, tailings and water recovery
Concentrate drains on a dewatering screen, while tailings settle in a thickener or lined pond and the clear water is pumped back to the circuit.
Which beneficiation circuit suits your chrome ore?
The right flowsheet depends on whether the ore is ferruginous or siliceous and how fine the chromite grains are. An Indian Bureau of Mines study of Sukinda plants found that older washing routes recovered only 40–50% of the chromite, while well-designed circuits reached 80–85%.
| Spirals and tables | The usual circuit for ferruginous ore of about 35–40% Cr2O3: crushing, rod mill, hydrocyclones, rougher and scavenger spirals, then tables. It is the route in our sample. |
|---|---|
| Jigs and tables | Used on siliceous ore of about 30–35% Cr2O3 where chromite frees at a coarser size; jigs take the 2–3 mm fraction and tables clean the reground finer product. |
| Slimes below 20 microns | Largely lost in plain gravity circuits; plants usually stockpile them for later ultrafine treatment rather than send them to waste. |
| Test work first | A laboratory or pilot test on your own ore fixes grind size, grade and recovery. CSIR-IMMT in Bhubaneswar has developed flowsheets and audited chrome ore plants in Odisha. |
Chrome ore and other inputs
Low-grade ore is the feed and the biggest cost. In December 2025 Odisha fines below 40% Cr2O3 averaged ₹9,708 per tonne against ₹23,131 for concentrates, per the Indian Bureau of Mines. Since each tonne of concentrate needs well over a tonne of ore, the plant's margin lives in that gap.
| Input | Share of cost | Year 3 (₹ lakh) |
|---|---|---|
| Low-grade chrome ore and fines (25 to 38% Cr2O3) | 82% | 481.50 |
| Sub-grade chrome ore lumps and chips | 15% | 88.08 |
| Flocculant and process consumables | 3% | 17.62 |
| Total | 100% | 587.20 |
Raw materials are 47% of sales in the sample. Ore prices move with each auction, so the report tests a rise in ore cost against DSCR.
Machinery for a chromite beneficiation plant
| Machine | What it does | Sample cost (₹ lakh) |
|---|---|---|
| Jaw crusher and hammer crusher | Breaks ore lumps to feed size | 30.24 |
| Rod mill for regrinding | Frees locked chromite with few slimes | 40.33 |
| Vibrating screens and sieve bend | Sizes feed and returns oversize | 22.68 |
| Hydrocyclone cluster with slurry pumps | Classifies and deslimes the slurry | 35.28 |
| Spiral concentrators | Rougher and scavenger separation | 37.81 |
| Wet shaking tables | Cleans concentrate to final grade | 35.28 |
| Thickener and water recycling system | Recovers process water from tailings | 30.24 |
| Dewatering screen and conveyors | Drains and moves concentrate | 20.16 |
| Total plant and machinery | 252.02 | |
Costs are the sample report's estimates for a 25 MT per day concentrate plant. Spiral starts, table decks, mill liners and rods wear and need a spares budget. Get current quotations before you finalise.
Water, power, manpower and land for the plant
A wet gravity plant moves far more water than ore, so water recovery and tailings storage decide the land you need as much as the machinery does.
| Water | Indicative: an 18,500 TPA chrome ore unit filed with SEIAA Odisha in 2024 used 153 KLD in circulation with about 13 KLD of make-up water, and committed to zero discharge. |
|---|---|
| Power and fuel | ₹161.20 lakh in Year 3 in our sample, 12.9% of sales, mainly for the crushers, rod mill and slurry pumps. |
| Manpower | 59 people in our sample: 9 in management, supervision and administration, 21 skilled operators and 29 semi-skilled and unskilled workers, with wages of ₹110.28 lakh in Year 1. |
| Land and buildings | ₹55.97 lakh for land and site development and ₹129.54 lakh for buildings and civil works in our sample, including covered ore and concentrate storage. |
| Tailings | A lined tailings pond or dry stack with room for several years of rejects; in the 2024 Odisha filing, tailings carried under 10% Cr2O3. |
Approvals for a chrome ore beneficiation plant
Beneficiation is treated as a mining-linked activity, so the approval list is longer than for a normal factory. These are the approvals we checked for Odisha as of October 2026.
| Environmental clearance | Mineral beneficiation is item 2(b) of the EIA Notification 2006. In Odisha, the state authority issued terms of reference to an 18,500 TPA unit in August 2024 and placed a 0.48 MTPA expansion in Category B1. |
|---|---|
| Pollution board consent | Consent to establish and operate from the State Pollution Control Board; Odisha lists "mining and ore beneficiation" in the Red category. Expect conditions on hexavalent chromium in water and tailings. |
| State mineral licence | Odisha's OMPTS Rules 2025 count beneficiation as processing. They require a mineral licence of up to five years, a platform-linked weighbridge, monthly returns and e-transit passes for every dispatch. |
| Indian Bureau of Mines | Registration on IBM's online system in Form K for those who trade, store or use major minerals, with monthly and annual returns. |
| Product specifications | BIS specifications for chromite include IS 10818 for metallurgical use, IS 10819 for refractories, IS 4737 for chemicals and IS 6788 for foundry sand. |
| Business registrations | Udyam and GST registration, a factory licence and power sanction for the connected load. |
Rules and categories differ by state and change over time. Confirm the current position with the state mines department and SPCB before you apply.
Who buys chrome concentrate?
Ferro alloy smelters take almost all of it. In 2019-20, ferro alloys including charge chrome used about 96% of the chromite consumed in India, according to the Indian Bureau of Mines. Those smelters feed the stainless steel industry.
India produced 3.79 million tonnes of chromite in 2021-22, and about 28% of it was below 40% Cr2O3. That low-grade ore is the feed that beneficiation plants upgrade.
- Ferro chrome and charge chrome producers
- Stainless steel makers with captive smelters
- Chrome refractory manufacturers
- Chromium chemical makers, such as sodium dichromate units
- Foundries that use chromite sand
Where a plant wins: buyers pay on analysis, so steady grade and silica control matter as much as tonnes. A plant that holds 50–52% Cr2O3 lot after lot can sell on a monthly contract instead of chasing spot buyers.
Mistakes that weaken a chromite beneficiation project report
- Sizing the plant without ore test work
Recovery and concentrate grade depend on your ore. Borrowed figures from another mine can overstate output by a wide margin.
- Selling every tonne at top grade
Concentrate is priced on Cr2O3, silica and the chromium to iron ratio. Revenue should follow the grade the circuit can hold, with penalties for off-spec lots.
- Ignoring slimes losses
Chromite ground below about 20 microns escapes spirals and tables. A report that assumes no fines loss overstates recovery.
- No firm ore supply
Low-grade ore often comes through auctions and trader lots. Lenders want to see where 12 months of feed will come from and at what grade.
- Under-sizing the tailings pond
Pond liners, water recycling and chromium monitoring are approval conditions. Leaving them out of cost and land plans delays consent.
How NPCS helps you plan a chromite beneficiation plant
- Ore and capacity planningMatch throughput, feed grade and target concentrate grade to the ore you can secure.
- Circuit and machineryCompare spiral, table and jig circuits and collect equipment quotations.
- Bank-ready project reportProjections, DSCR, ore price sensitivity and working capital in your lender's format.
- Approvals and site layoutPlant, storage and tailings layout plus the clearance and licence list for your state.
NPCS's client list includes 25 assignments in industrial minerals, one of them for chromite beneficiation, and the NPCS project team has prepared project reports since 1994.
What's inside the chromite beneficiation sample report
- Introduction
- Uses and applications
- Market potential
- Manufacturing process
- Raw materials
- Plant and machinery
- Land, building and utilities
- Manpower
- Licences and approvals
- Project cost and means of finance
- Working capital
- Projected profitability
- Cash flow statement
- Projected balance sheet
- Depreciation
- Term loan repayment
- Debt service coverage
- Break-even analysis
- Financial ratios
- Key assumptions
- Conclusion
- Monthly loan repayment schedule
19 pages, five-year projections, illustrative figures.
Open sample reportFree sample or a report for your project?
| What you get | Free sample | NPCS report for your project |
|---|---|---|
| Capacity and location | Typical unit | Your capacity, site and state |
| Figures | Illustrative | Built on current prices and quotations |
| Machinery suppliers and quotations | No | Yes |
| Market survey for your region | No | Yes |
| Bank or scheme format (PMEGP, term loan) | No | Yes |
| Use for a loan application | No | Yes |
Real NPCS chromite beneficiation project reports
These are chromite beneficiation project reports NPCS has prepared, with the plant capacity, total capital investment, rate of return and break-even worked out in each. Costs have moved since some were written, so we bring any of them up to date for your capacity and location.
| Project report | Plant capacity | Total investment | Rate of return | Break-even | Action |
|---|---|---|---|---|---|
| Chromite Beneficiation | 18,000 MT/Annum Chromite Concentrate | ₹3.66 crore | 41% | 65% | Get this report |
Figures as worked out in each NPCS report. Total investment includes plant and machinery, land and building, and working capital.
What clients say about NPCS
4.7
264 Google reviews, as of 20 Oct 2026
Clients most often mention
- feasibility reports 18
- project report 16
- helpful for startups 15
- detailed reports 8
-
Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.
Piyush Singh, Google review, 2026
-
Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended
Saroj Yadav, Google review, 2026 View on Google
-
In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.
Shrishti Gautam, Google review, 2026
-
NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.
Raj Yadav, Google review, 2026
Chromite Beneficiation project report: frequently asked questions
How much does a chromite beneficiation plant cost in India?
Our sample report models a plant making 25 MT of concentrate a day at a total project cost of ₹546.50 lakh, including ₹252.02 lakh of machinery. A chrome ore unit of 18,500 TPA throughput filed with SEIAA Odisha in August 2024 put its cost at about ₹5.2 crore. Cost rises with throughput, grinding needs and the size of the tailings pond.
What grade of concentrate does a chromite beneficiation plant produce?
Most Indian plants aim for a concentrate of about 50–52% Cr2O3. An Indian Bureau of Mines study of Sukinda plants reported composite concentrates of about 52% Cr2O3 at 80–85% recovery from ores carrying 30–40% Cr2O3. Buyers also check silica and the chromium to iron ratio, so a plant should test its own ore before fixing a grade.
Which machines are used in chromite beneficiation?
A typical gravity plant uses a jaw crusher, a hammer crusher, vibrating screens and a rod mill to prepare the feed. Hydrocyclones, spiral concentrators and wet shaking tables do the separation, with a thickener and dewatering screen at the end. Siliceous ores with coarse chromite may add jigs. In our sample the rod mill is the largest single machinery item at ₹40.33 lakh.
Is environmental clearance needed for a chrome ore beneficiation plant?
Yes. Mineral beneficiation is item 2(b) of the EIA Notification 2006, and Odisha appraises chrome ore units through SEIAA. Even an 18,500 TPA unit received standard terms of reference in August 2024. You also need consent from the pollution board, which lists ore beneficiation in the Red category in Odisha, and a state mineral licence.
Is chromite beneficiation profitable?
It can be, but margins are thin and depend on ore cost and recovery. Our illustrative sample earns a 14% return on investment in Year 3, with break-even at about 50% of capacity, an average DSCR of 1.40 and payback in about 4.6 years. A few points of extra recovery change profit more than any other assumption.
Where should a chromite beneficiation plant be located?
Close to the ore. More than 96% of India's chromite resources are in Odisha, mostly in Jajpur, Kendujhar and Dhenkanal districts, according to the Indian Bureau of Mines. A plant near the Sukinda valley saves freight on ore that is half waste, and sits close to the ferro chrome smelters that buy the concentrate.
Is the sample report free and can I use it for a bank loan?
The sample project report PDF is free to view and download. It is an illustrative report that shows the format and depth of an NPCS report. Its figures are representative and not based on a real project, so do not submit it to a bank. For a loan, NPCS prepares a report for your own ore, capacity, site and lender.
Sources and references
- Indian Minerals Yearbook 2022: Chromite (advance release)Indian Bureau of Mines, Ministry of Mines, checked Oct 2026
- Average sale price of minerals, December 2025Indian Bureau of Mines, Ministry of Mines, checked Oct 2026
- Beneficiation practices in the Sukinda valley area chromite deposits (2006)Indian Bureau of Mines authors, CSIR-NML repository, checked Oct 2026
- Terms of reference for an 18,500 TPA chrome ore beneficiation plant, BhadrakSEIAA Odisha, Parivesh portal, checked Oct 2026
- Standard terms of reference for a chrome ore beneficiation plant expansion, JajpurSEAC Odisha, Parivesh portal, checked Oct 2026
- Red category industries listState Pollution Control Board, Odisha, checked Oct 2026
- Odisha Minerals (Prevention of Theft, Smuggling and Illegal Mining and Regulation of Possession, Storage, Trading and Transportation) Rules 2025Government of Odisha, checked Oct 2026
- FAQ on registration and monthly and annual returnsIndian Bureau of Mines, checked Oct 2026
- Chrome ore beneficiationCSIR-Institute of Minerals and Materials Technology, checked Oct 2026
