What is a forging unit for automobile spare parts project report?
A forging unit for automobile spare parts project report is a detailed project report (DPR) for a plant that forges steel bars into auto parts in closed dies. Typical parts are connecting rods, gears, axle and steering parts. It sets out the process, machinery, steel grades, buyers, project cost, finance, five-year projections, DSCR and break-even.
Promoters use it to size the press line and raise a term loan; banks use it to judge whether the plant can repay from its own cash flow.
Also known as: auto parts forging project report, automobile forging plant DPR, closed die forging unit project report, forging business plan.
Forging unit for automobile spare parts: plant cost in India and returns
The sample report models a closed die forging unit of 5.5 MT per day, or 1,815 MT a year at full capacity, running 330 days. It starts at 60% capacity and reaches 80% in Year 5, selling heat-treated rough forgings at ₹1,45,000 per MT.
| Land and site development | 69.13 |
|---|---|
| Building and civil works | 255.77 |
| Plant and machinery | 455.11 |
| Other fixed assets | 56.62 |
| Contingencies | 35.54 |
| Preliminary and pre-operative | 21.80 |
| Working capital margin | 63.21 |
| Total | 957.18 |
| Promoter's contribution (25%) | 239.30 |
|---|---|
| Term loan from bank (75%) | 717.88 |
| Cash credit limit (separate) | 189.64 |
| Total project cost | 957.18 |
Term loan at 10.5% with a 6-month moratorium and 54 monthly instalments. Lowest DSCR in any year is 1.81. All figures are illustrative.
Forging unit for automobile spare parts manufacturing process
Most auto parts are made by closed die hot forging, where a heated billet is squeezed into a shaped steel die. Each part number needs its own die set, so the die shop is as much a part of the line as the press.
- Bar cutting
Steel bars are sheared or sawn into billets of a fixed weight; weight control here decides how much flash you lose later.
- Induction heating
Billets pass through an induction coil and reach forging heat, about 1,150 to 1,200 °C, in a minute or two with little scale.
- Closed die forging
The press or hammer forms the billet through blocker and finisher impressions, with graphite lubricant sprayed on the hot die.
- Trimming and piercing
A trimming press cuts away the thin flash ring and punches holes while the forging is still hot.
- Heat treatment
Forgings are normalised, or hardened and tempered at roughly 700–900 °C, to reach the hardness and grain structure on the drawing.
- Shot blasting
Steel shot removes scale so surface cracks, laps and folds can be seen during inspection.
- Inspection and dispatch
Parts are checked for hardness, cracks by magnetic particle testing, and dimensions, then sent to the machining customer in bins.
Drop hammer, screw press or mechanical press: which route suits auto forgings?
The forming machine sets the parts you can make, the die life you get and the power you draw. In the TERI study of the Pune forging cluster for SIDBI, small units ran belt drop hammers of 0.5–3 tonnes and screw presses of 100–1,500 tonnes, mostly with oil-fired furnaces.
| Drop hammer | Lowest cost to start and flexible for small batches. Repeated blows give wider weight variation and more noise and vibration, so foundations cost more. |
|---|---|
| Friction screw press | One controlled stroke per part, good for flanged parts and gear blanks. A sensible middle path for a first unit serving tractor and aftermarket buyers. |
| Mechanical forging press | Fixed stroke and high output, with tighter tolerances and longer die life. Common in plants that supply vehicle makers with connecting rods, crankshafts and steering parts, but it costs the most. |
| Oil or gas fired furnace | Cheaper to buy, but heats slowly, forms more scale and puts the unit in the orange pollution category in states that follow the CPCB list. |
| Induction billet heater | Heats each billet in sequence with less scale and steadier temperature. Uses about 450–500 kWh per tonne heated, so it needs an HT power connection. |
Our sample report uses a mechanical or friction screw press with an induction heater. Energy figures are from the TERI study for SIDBI; check current machine data with suppliers.
Steel grades and raw materials for auto forgings
Hot rolled bars and billets are bought in the grade the buyer's drawing names. Plain carbon grades such as 15C8, EN8 or C45 suit shafts and levers, while case-hardening grades such as 20MnCr5 or SAE 8620 suit gears. Each batch needs a mill test certificate, because buyers trace every forging back to its heat number.
| Raw material | Share of cost | Year 3 (₹ lakh) |
|---|---|---|
| Carbon and alloy steel bars and billets | 93% | 954.77 |
| Hot work die steel blocks | 5% | 51.33 |
| Graphite die lubricant | 2% | 20.53 |
| Total | 100% | 1,026.63 |
In the sample, raw materials are 55.7% of sales in Year 3. Die steel is shown as a raw material because dies wear out and are re-sunk or replaced through the year.
Machinery for a forging unit and its cost
The forging press with its dies is the largest single item in the sample, followed by the induction heater and the die shop. Buyers visiting for approval look closely at the die shop and lab, so they are not places to cut.
| Machine | What it does | Sample cost (₹ lakh) |
|---|---|---|
| Mechanical or friction screw forging press with dies | Forms the hot billet into the part | 145.63 |
| Induction billet heater | Heats billets to forging temperature | 77.37 |
| Die shop with CNC milling and EDM machines | Makes and re-sinks die impressions | 59.16 |
| Heat treatment furnaces for hardening and tempering | Sets hardness and grain structure | 54.61 |
| Trimming and piercing press | Removes flash and punches holes | 36.41 |
| Bar shearing machine and band saw | Cuts bars into billets | 27.31 |
| Shot blasting machine | Cleans scale before inspection | 27.31 |
| Testing lab with spectrometer, hardness tester and crack detector | Checks chemistry, hardness and cracks | 27.31 |
| Total plant and machinery | 455.11 | |
Costs are the sample report's estimates for a 5.5 MT per day line. Get current quotations before you finalise.
Power and manpower for an auto parts forging plant
Heating takes 80–90% of the energy a forging unit uses, so the heater decides your power bill. In the sample, power and fuel cost ₹113.17 lakh in Year 3. The unit employs 40 people, with skilled press, heater and die shop operators forming the core team.
| Staff category | Number | Monthly wage (₹) | Year 1 cost (₹ lakh) |
|---|---|---|---|
| Management, supervision and administration | 6 | 30,500 | 21.96 |
| Skilled workers and operators | 14 | 19,500 | 32.76 |
| Semi-skilled and unskilled workers | 20 | 13,000 | 31.20 |
| Total | 40 | 85.92 |
Wages rise 5% a year in the sample projections. A unit running two shifts needs more operators than shown here.
Licences and approvals for a forging unit
| Business registration | Udyam (MSME) registration and GST registration |
|---|---|
| Pollution board consent | Consent to establish and operate from the State Pollution Control Board. Forging with oil or gas fired furnaces is in the orange category on the CPCB-based list; ask the board how it treats induction heating |
| Factory licence and power | Factory licence where worker and power thresholds apply, and an HT power connection sanctioned for the heater and press load |
| Steel input standard | Carbon steel billets and bars for forgings (IS 1875) are on the Ministry of Steel's Quality Control Order list, so buy BIS-marked material with mill certificates |
| Quality system | ISO 9001 at start; IATF 16949 certification when you supply vehicle makers or tier 1 suppliers |
| GST on parts | Auto parts moved to a single 18% GST rate in the September 2025 rate changes; confirm the HSN code for each forging with your CA |
Who buys automobile forgings and how a new unit gets orders
Demand follows production of two-wheelers, cars, tractors and commercial vehicles, plus the replacement market for worn steering, suspension and transmission parts. Large forging companies serve vehicle makers directly, while smaller units supply rough forgings to machining shops and spare parts brands.
- Tier 1 auto component suppliers who machine and assemble
- Machining and gear cutting units
- Tractor and farm equipment makers
- Aftermarket spare parts brands and distributors
- Two-wheeler and three-wheeler makers
Approval takes time: a buyer approves each part number only after sample lots, dimensional reports and metallurgy tests. Plan for the first year's sales to come from aftermarket and tractor parts while vehicle maker approvals progress.
Mistakes that weaken a forging unit project report
- Costing steel on finished weight
Flash, scale and end pieces mean input weight is well above the net weight of each forging. Price and steel cost must be worked per part on gross input weight.
- No budget for new dies
Every new part number needs a die set and trial runs. Leaving die development out understates both capital cost and the time to first sales.
- Fixed selling prices with moving steel prices
Auto buyers usually revise forging prices with steel on an agreed index. A report that assumes fixed prices hides the risk in between revisions.
- Full capacity from day one
A press line rarely runs full in Year 1 because part approvals come one by one. Banks expect a ramp-up such as the 60% start in our sample.
- Ignoring rejection and rework
Laps, cracks and hardness misses are scrapped or re-heat-treated. Rejection allowances belong in both output and cost.
How NPCS helps you plan a forging unit for automobile spare parts
- Part mix and press sizingMatch target parts and weights to the press, heater and die shop you need.
- Machinery and route choiceCompare hammer, screw press and mechanical press lines and get quotations.
- Bank-ready project reportProjections, DSCR, steel price sensitivity and working capital in your lender's format.
- Approvals and layoutPlant layout, power load, pollution consent and the approvals list for your state.
NPCS's client list shows 116 assignments in the metal products sector. The NPCS project team, led by founder Ajay Kumar Gupta, has prepared project reports since 1994.
What's inside the forging unit for automobile spare parts sample report
- Introduction
- Uses and applications
- Market potential
- Manufacturing process
- Raw materials
- Plant and machinery
- Land, building and utilities
- Manpower
- Licences and approvals
- Project cost and means of finance
- Working capital
- Projected profitability
- Cash flow statement
- Projected balance sheet
- Depreciation
- Term loan repayment
- Debt service coverage
- Break-even analysis
- Financial ratios
- Key assumptions
- Conclusion
- Monthly loan repayment schedule
18 pages, five-year projections, illustrative figures.
Open sample reportFree sample or a report for your project?
| What you get | Free sample | NPCS report for your project |
|---|---|---|
| Capacity and location | Typical unit | Your capacity, site and state |
| Figures | Illustrative | Built on current prices and quotations |
| Machinery suppliers and quotations | No | Yes |
| Market survey for your region | No | Yes |
| Bank or scheme format (PMEGP, term loan) | No | Yes |
| Use for a loan application | No | Yes |
Real NPCS forging unit for automobile spare parts project reports
These are forging unit for automobile spare parts project reports NPCS has prepared, with the plant capacity, total capital investment, rate of return and break-even worked out in each. Costs have moved since some were written, so we bring any of them up to date for your capacity and location.
| Project report | Plant capacity | Total investment | Rate of return | Break-even | Action |
|---|---|---|---|---|---|
| Forging Unit for Automobile Spare Parts | 6 MT / Day | ₹4.35 crore | 42% | 63% | Get this report |
Figures as worked out in each NPCS report. Total investment includes plant and machinery, land and building, and working capital.
What clients say about NPCS
4.7
264 Google reviews, as of 20 Oct 2026
Clients most often mention
- feasibility reports 18
- project report 16
- helpful for startups 15
- detailed reports 8
-
Excellent experience with Niir Project Consultancy Services. Their Techno-Economic Feasibility Reports are incredibly detailed and backed by solid market data.
Piyush Singh, Google review, 2026
-
Niir Project Consultancy Services offers excellent guidance for business setup. Their market survey and feasibility reports saved us a lot of time and helped us make informed decisions. Highly recommended
Saroj Yadav, Google review, 2026 View on Google
-
In an era of information overload, NIIR stands out for its precision. Their technical consultancy and market feasibility studies are world-class.
Shrishti Gautam, Google review, 2026
-
NIIR Project Consultancy Services provides useful books and reports for students, entrepreneurs, and small businesses. Their content is easy to understand and focuses on practical ideas for starting and managing industries. Overall, NIIR is helpful for learning about business and project planning.
Raj Yadav, Google review, 2026
Forging Unit for Automobile Spare Parts project report: frequently asked questions
How much does it cost to set up a forging unit for automobile spare parts?
A small hammer shop with one or two drop hammers and an oil-fired furnace needs roughly ₹1–3 crore. Our sample report models a 5.5 MT per day press line with induction heating and its own die shop at ₹957 lakh. Automated lines with heavy presses run to ₹20 crore and more. These ranges are indicative and depend on press size and location.
Is a forging unit for auto parts profitable?
It can be, if the press stays loaded. In our illustrative sample, the unit earns a 27% return on investment in Year 3, breaks even at 32% of capacity and pays back in about 3.1 years. Real results depend on steel price pass-through in buyer contracts, die life, rejection rates and how quickly you win approved part numbers.
Which machines are needed for a forging unit?
The core line is a bar shearing machine or band saw, an induction billet heater, a forging press or hammer with dies, and a trimming press. After forging you need heat treatment furnaces and a shot blasting machine. A die shop with CNC milling and EDM, and a lab with a spectrometer, hardness tester and crack detector, complete the plant.
What raw material is used for forging automobile parts?
Hot rolled carbon and alloy steel bars and billets are the main input. The buyer specifies the grade, such as EN8 or C45 for shafts and 20MnCr5 or SAE 8620 for gears. In our sample report steel is 93% of raw material cost. The rest is hot work die steel for dies and graphite lubricant.
Do I need IATF 16949 certification to supply forgings to vehicle makers?
It is not a legal licence, but vehicle makers and tier 1 suppliers commonly ask for it before approving a forging source. IATF 16949 is the automotive quality management standard built on ISO 9001. Many new units start with aftermarket and machining customers and take up certification once their process records are in place.
Forging ka business kaise shuru kare?
Start by choosing the part family you will forge and the buyers you can reach, such as tractor or aftermarket parts. Then size the press and heater for those parts, get a project report with projections and DSCR, arrange land and an HT power connection, and apply for pollution consent. Sample trials with buyers usually run in parallel with commissioning.
Is the sample report free and can I use it for a loan?
The sample is free to view and download. It is an illustrative report that shows the format and depth of an NPCS report. Its figures are representative and not based on a real project, so it should not be submitted to a bank. For a loan, NPCS prepares a report for your own parts, capacity, location and lender.
Sources and references
- Cluster profile report: Pune forging clusterTERI for SIDBI (WB-GEF-SIDBI project, 2012), checked Oct 2026
- Categorization of industrial sectors under Orange as per CPCB criteriaState Pollution Control Board, Odisha, checked Oct 2026
- Quality Control Orders for steel products (Lok Sabha unstarred question 3149)Ministry of Steel, Government of India, checked Oct 2026
- GST rate changes for vehicles and auto parts, New India Samachar, 1–15 October 2025Press Information Bureau, Government of India, checked Oct 2026
- IATF 16949:2016 automotive quality managementBSI (British Standards Institution), checked Oct 2026
