Power Project, Power Generation Plants, Hydroelectric Power, Gas-Fired Power Station, Coal, Thermal, Water, Hydro, Wind, Solar, Agro, Biogas Based Power Plants, Electrical Power Industry, Alternative, Renewable Power Generation, Electricity Generation

India possesses one of the largest power generation capacities in the world (its current ranking is fifth) with an installed capacity of 156,000 MW which is about 4 percent of global power generation. The top four countries, viz., US, Japan, China and Russia together consume about 49 percent of the total power generated globally. The average per capita consumption of electricity in India is estimated to be 704kWh during 2008-09. The power sector has emerged as major focus area for the government both central and state. However, it suffers from power shortages estimated at 14-15 per cent, with the figure higher in the northern and western regions.  

India's generation capacity of 2,300 MW in 1950 expanded to over 116,500 MW including non-utilities at the end 2000-01. The total installed capacity of electric power generation further increased to 141,080 MW in 2007-08 (upto January 2008) compared to a capacity of 128,000 MW during the same period in 2006-07. The Eleventh Plan has targeted a capacity addition of 78,570 MW. The five years (2007-2012) may be the best of times for power equipment makers with the power sector on an expansion spree. With order-book growth expanding over the last three years, there is a good chance that this will continue. Close to 82% of the planned generation capacity for the Tenth Plan was either implemented or was in the process of being implemented. Even assuming a 70% implementation ratio for the Eleventh Plan, close to 55,000 MW will be added. Five ultra mega power projects, totaling 20,000 MW are coming up in 2008. In the transmission sector, for example, Power Grid Corporation is planning a capex of Rs 710 billion by 2010.

Earlier, the shortfalls in achieving the Plan targets of addition to power generation and up-gradation of transmission and distribution had adversely affected the electrical equipment industry. The peak shortage which was over 11% of the requirement in 2003-04 increased to 11.7% in 2004-05 and to over 12% in 2005-06. The shortage further rose to about 14% in 2006-07. In the ten months of 2007-08 the peak shortage had risen to over 15% of the peak demand of 107,010 MW.

The national grid envisage 200,000 MW transmission capacity and 37,700 MW of inter-regional power transfer capacity (current inter-regional power transfer capacity is 20,750 MW) to ensure smooth transfer of power from power –surplus to power-deficit regions.

According to the Power Ministry, the power sector has tied up Rs 2,240 billion worth of investments to build power plants with 70,000 MW capacities in the next three years. The Indian government has set ambitious goals in the 11th plan for power sector owing to which the power sector is poised for significant expansion. In order to provide availability of over 1000 units of per capita electricity by year 2012, it has been estimated that need-based capacity addition of more than 100,000 MW would be required. This has resulted in massive addition plans being proposed in the sub-sectors of Generation Transmission and Distribution. Investment is also expected to flow into different segments of the value chain, covering the segments of power generation, transmission and distribution and allied sectors such as equipment, technology and services. The private sector is expected to play a more active role in investment and capital productivity. The government has undertaken a number of initiatives to facilitate private sector participation.

With some fast moves at launching fast track projects to augment supplies, the Indian industry needs to improve its competitiveness. The Indian market is growing and multinationals with newer technologies are now more active.

We can provide you detailed project reports on the following topics. Please select the projects of your interests.

Each detailed project reports cover all the aspects of business, from analysing the market, confirming availability of various necessities such as plant & machinery, raw materials to forecasting the financial requirements. The scope of the report includes assessing market potential, negotiating with collaborators, investment decision making, corporate diversification planning etc. in a very planned manner by formulating detailed manufacturing techniques and forecasting financial aspects by estimating the cost of raw material, formulating the cash flow statement, projecting the balance sheet etc.

We also offer self-contained Pre-Investment and Pre-Feasibility Studies, Market Surveys and Studies, Preparation of Techno-Economic Feasibility Reports, Identification and Selection of Plant and Machinery, Manufacturing Process and or Equipment required, General Guidance, Technical and Commercial Counseling for setting up new industrial projects on the following topics.

Many of the engineers, project consultant & industrial consultancy firms in India and worldwide use our project reports as one of the input in doing their analysis.

We can modify the project capacity and project cost as per your requirement.
We can also prepare project report on any subject as per your requirement.

Page 1 of 3 | Total 27 projects in this category
«   Page 1 2 3   Next »

Add multiple items to inquiry
Select the items and then press Add to inquiry button

Select all | Clear all Sort by

Power Project For Glass Industry

Glass industry in India is one of the prime industry where much more power is utilizing for controlling the production of glass continuously. It is necessary to regular supply of power in the industry. On that base it is best to produce captive power in their own industry. Now government wants to increase the captive power project as well as they increase the power production by using non-conventional source of energy power from the waste utilization and solar energy. India support an installed capacity of 79, 187MW the maximum peak availability is only 53000MW, entailing a supply deficit of 9% and 21% peaking shortage. India requires 1.4 lakhs MW of additional capacity in the next 15 years to merely keep pace with the current shortage. This means an investment of nearly $120 billion.
Plant capacity: 100-110MW/DayPlant & machinery: 453 Lakhs
Working capital: -T.C.I: 494 Lakhs
Return: 56.15%Break even: 52.21%
Add to Inquiry Add to Inquiry Basket

Sponge Iron Including Power Plant

Sponge iron is the iron manufactured by refining iron ore. Iron ore is refined by burning off its wastes to a considerable extent. It is used as a substitute of scrap used in Iron and steel making in electrical are furnaces or induction furnaces. It is also known as direct reduced iron. Sponge iron is becoming increasingly important all over the world as a raw material for high quality steel, due to acute shortage and high price good quality melting scrap. Sponge iron is considered as a good product mixes, for making high value steel industries which are using especially electrical arc furnaces. It is expected that demand of steel will grow because of emerging growth in steel consuming segment. There is good scope for new entrepreneurs.
Plant capacity: 450.00 MT/DayPlant & machinery: Rs. 56 Crores
Working capital: Rs. 11 CroresT.C.I: Rs. 83 Crores
Return: 37.49%Break even: 49.41%
Add to Inquiry Add to Inquiry Basket

Steel Tubes From Scraps And P.V.C. Pipe With 5mw/Hr. Captive Power Plant

Steel tube and P.V.C. pipes are largely used in the commercial, industrial and agricultural field. In agricultural field PVC pipes are largely used when M.S. tubes have slightly uses. These pipes has very good demand not only in India but globally. Adding the captive power plant with this unit will be beneficial. The entrepreneurs who want to venture into this field will be successful.
Plant capacity: 280 MT/ Day Steel Tubes120 MT/ Day PVC Pipes 5MW/Hr. Captive Power PlantPlant & machinery: Rs. 2415 Lakhs
Working capital: -T.C.I: Rs. 4316 Lakhs
Return: 41.27%Break even: 63.16%
Add to Inquiry Add to Inquiry Basket

Power Project For Glass Industry

Glass industry in India is one of the prime industry where much more power is utilizing for controlling the production of glass continuously. It is necessary to regular supply of power in the industry. On that base it is best to produce captive power in their own industry. Now government wants to increase the captive power project as well as they increase the power production by using non-conventional source of energy power from the waste utilization and solar energy. India support an installed capacity of 79, 187MW the maximum peak availability is only 53000MW, entailing a supply deficit of 9% and 21% peaking shortage. India requires 1.4 lakhs MW of additional capacity in the next 15 years to merely keep pace with the current shortage. This means an investment of nearly $120 billion.
Plant capacity: 110 MW/DayPlant & machinery: 453 Lakhs
Working capital: -T.C.I: 494 Lakhs
Return: 56.00%Break even: 52.00%
Add to Inquiry Add to Inquiry Basket

Biogas Power Plant from Cow Dung

Biogas plants have the ability to accept a wide variety of organic residues as primary fuel input. This includes Cow dung, agricultural residue, effluent discharge, food residue etc. Most agricultural / food production processes have significant amount of organic residues output as by-product. Traditionally, there residues are buried in landfills or discharged, which cause negative environmental impact. In some places, institutions have to pay a fee to dispose off such residues. A biogas plant solves this residue disposal problem by converting residues into usable energy. Biogas is created by bacteria in the process of bio-degradation of organic material under anaerobic (without air) conditions. Methanogens material and return the decomposed products to the environment. In this process biogas (methane) is generated, which is a source of renewable energy. There is a good scope for new entrants.
Plant capacity: 1000 KWh or 1 MWhPlant & machinery: Rs. 485 Lakhs
Working capital: -T.C.I: Rs. 1245 Lakhs
Return: 22.00%Break even: 45.00%
Add to Inquiry Add to Inquiry Basket

BIO MASS GASIFICATION POWER PLANT

Bio-gas power plant is one of the sources of non-conventional energy. The biomass fuels are solid carbonaceous materials derived from living plants and animals. There is availability of waste material in our country, producer gas can be easily converted to energy. It can be used for providing electricity in nearer or furthest area. It can also be used to run plant and machineries in the industry. Economic development results in both qualitative and quantitative increase in the use of energy. In India, it is estimated that of the 68.3 million tonnes of carbon released annually due to biomass burning, fuel wood accounts for 82.3%. It will be profitable for any new entrant to invest in this field.
Plant capacity: 1000 KWh or 1 MW.Plant & machinery: 475 Lakhs
Working capital: -T.C.I: 691 Lakhs (W/c. One Month)
Return: 12.00%Break even: 66.00%
Add to Inquiry Add to Inquiry Basket

Solar Power Plant

Solar thermal systems for generating electricity use tracking mirrors to reflect and concentrate sunlight on to a receiver, where, it is converted to high temperature thermal energy. The high-temperature heat in the receiver is then used to drive a heat engine and electric generator to produce electricity. The solar energy ultimately heats a fluid powering a small engine / generator operating at about 8000C, a single dish module can generate up to 50 KW of electric power. Many dishes can be grouped together to produce more power. Most of the processes involve a lot of capital as well as recurring expenditure. Solar power has an edge over all the other non-conventional forms of energy sources as it is non-polluting. The solar energy is abundant and is available at all parts of the world through out the year. There is a good scope for new entrants.
Plant capacity: -Plant & machinery: -
Working capital: -T.C.I: -
Return: N/ABreak even: N/A
Add to Inquiry Add to Inquiry Basket

CO-GENERATION POWER PLANT BASED ON BAGASSE

Co-generation plant based on Bagasse is the need of the hour in the perspective of the power generation required and its demand is increasing considerably. There stands an imperative need for the setting up of power plant based on bagasse, which is a waste product from sugar industries. Co-generation is the simultaneous production of process heat and electric power using single fuel. Biomass fuel can also be used in co-generation plants for enhancing their efficiency. Co-generation facilities increase economic viability and profitability of an industry. In sugarcane industries it is most popular environment friendly way of producing electricity using sugarcane bagasse. Co-generation projects based on agro waste like rice husk, bagasse etc. as fuel result is lowering the cost of energy generation, low capital investment, higher profitability of plant. It is a lucrative project with very bright future prospects. A new entrepreneur can venture into this field.
Plant capacity: 15 MW Plant & machinery: 850 Lakhs
Working capital: -T.C.I: Cost of Project : 1746 Lakhs
Return: 53.00%Break even: 46.00%
Add to Inquiry Add to Inquiry Basket

CO-GENERATION POWER PLANT BASED ON BAGASSE

Co-generation plant based on Bagasse is the need of the hour in the perspective of the power generation required and its demand is increasing considerably. There stands an imperative need for the setting up of power plant based on bagasse, which is a waste product from sugar industries. Co-generation is the simultaneous production of process heat and electric power using single fuel. Biomass fuel can also be used in co-generation plants for enhancing their efficiency. Co-generation facilities increase economic viability and profitability of an industry. In sugarcane industries it is most popular environment friendly way of producing electricity using sugarcane bagasse. Co-generation projects based on agro waste like rice husk, bagasse etc. as fuel result is lowering the cost of energy generation, low capital investment, higher profitability of plant. It is a lucrative project with very bright future prospects. A new entrepreneur can venture into this field.
Plant capacity: 15 M W Plant & machinery: 850 Lakhs
Working capital: -T.C.I: Cost of Project : 1746 Lakhs
Return: 53.00%Break even: 46.00%
Add to Inquiry Add to Inquiry Basket

Transmission Tower & Tele Communication Tower with Galvanizing Plant

The purpose of a transmission line tower is to support conductors carrying electrical power and one or two ground wires at suitable distances above the ground level and from each other. A transmission line tower is a space-frame and high order indeterminate structure. Its cost is influenced by its weight. Reliability of a transmission structure depends not only upon its design, but also on the development of structural arrangement, detailing of connections, uniformity of quality of structural sections, accurate fabrication, erection in the field and ultimately maintenance. Transmission lines are subjected to various loads during their lifetime. These loads are classified into climatic loads, failure containment loads and construction and maintenance loads. Proper fabrication while maintaining permissible tolerance, galvanizing and testing of towers are very essential. An economical foundation design and proper erection techniques are also very vital for the safety of the tower. The demand is growing for mobile telephony towers. There is an increasing demand for telecom towers in rural/semi-urban areas as the penetration is still very low. The demand for telecom towers is also a function of steadily growing subscriber base and higher usage time of subscribers. India would have an estimated 42.5 crore mobile subscribers by 2010, creating a demand for 4.5 lakh base transmission stations, with major demand coming from rural areas. There is a good scope for new entrants.
Plant capacity: 24,000 MT /YearPlant & machinery: 149 Lakhs
Working capital: -T.C.I: Cost of Project : 716 Lakhs
Return: 46.00%Break even: 53.00%
Add to Inquiry Add to Inquiry Basket

Information
  • One Lac / Lakh / Lakhs is equivalent to one hundred thousand (100,000)
  • One Crore is equivalent to ten million (10,000,000)
  • T.C.I is Total Capital Investment
  • We can modify the project capacity and project cost as per your requirement.
  • We can also prepare project report on any subject as per your requirement.
  • Caution: The project's cost, capacity and return are subject to change without any notice. Future projects may have different values of project cost, capacity or return.

Add multiple items to inquiry
Select the items and then press Add to inquiry button

Page 1 of 3 | Total 27 projects in this category
«   Page 1 2 3   Next »

About NIIR PROJECT CONSULTANCY SERVICES

Hide »

NIIR PROJECT CONSULTANCY SERVICES (NPCS) is a reliable name in the industrial world for offering integrated technical consultancy services. Its various services are: Pre-feasibility study, New Project Identification, Project Feasibility and Market Study, Identification of Profitable Industrial Project Opportunities, Preparation of Project Profiles and Pre-Investment and Pre-Feasibility Studies, Market Surveys and Studies, Preparation of Techno-Economic Feasibility Reports, Identification and Selection of Plant and Machinery, Manufacturing Process and or Equipment required, General Guidance, Technical and Commercial Counseling for setting up new industrial projects and industry.

NPCS also publishes varies technology books, directory, databases, detailed project reports, market survey reports on various industries and profit making business. Besides being used by manufacturers, industrialists and entrepreneurs, our publications are also used by Indian and overseas professionals including project engineers, information services bureau, consultants and consultancy firms as one of the input in their research.

^ Top

Products & Services

Others

Contact Us

My Account

Help

Payment Options

  • Credit Cards
  • Debit Cards
  • PayPal
  • Net Banking - (All Major Indian Banks)

We Process

  • Cards

Google Search


Search Project Report & Profiles





Subjects